Viewing all customer Discussions for:

39-419 RH Awning Operator, 3/8" Hole

Good Afternoon, I was looking to figure out what type of operators these are. I am not sure of the brand. If you need any more pictures I would be happy to send more. I also need to replace the weather stripping and do not know what type to get. Thank you

Can you please help me order the correct replacement for the entire crank pictured below. It is for 1960s jaulosie windows. Left hand side. All associated parts needed. There are no markings anywhere on the old crank.

Patio window operator No part number on it

No markings or numbers. Windows were custom made. They are awning windows

This is a left hand I also need a right hand. Looking for 2 of each.

This is a right hand window crank from an older SW Florida home. There is no writing of any type. As shown in the picture the arm has a small threaded hole.

I just received my RH Awning Operator (3/8" hole, Part # 39-419). With it there are several parts to link its arm to the arm of the awning window, including a 5/16" Shoulder Crew, 1/4" - 20 Thread (Part # 33-070). Also included is a #10 X 1/2" Pan Head Phillips Screw (Part # 33-081). What I need ar ... (cont.)

I am not able to identify any that match mine on your website. Do you have any recommendations? Please let me know if you need any information for me.

Can you help me on this? I am attaching a picture of the part I need to replace. Do you have this? I measured the following: 5 3/4" long 2" deep 1" wide If you have the part I would like to order it. Much appreciated. Best regards,

I cannot find any markings on the window or parts. The windows are probably 55 to 60 years old. It is the threads on the piece that attaches the handle to the opener that have worn off. I hope you can help me.

The window will not crank open or close and the handle is stripped

I am looking for an awning window crank replacement and I will get close with a part but one of the dimensions will not be exactly right. It is a white RH awning crank with 2 screws at the top, 2 at the bottom with 5 1/4 inches between, top screws have 1/2 in. spacing between center of screw to cent ... (cont.)

I need one that the crank handle swings out to the opposite. Would that be left or right handed? It looks like part #39-420/419 might be it. Sent from my iPhone

Hello, I need an awning crank, and I believe the part 39-026 is what I need. Based on the picture attached, does that seem correct? Thank you! Our windows are old, and I cannot locate any brand name or numbers

Need replacements for old window cranks. House is old and nothing is standard. Can't identify manufacturer, although Swisco seems to be very close, if not it exactly. Crank base has the following part no engraved inside: PT NO 10-9231-LH-4.

The dimensions on the 39-419 are the same as the one I need except the length from the rivet to the center of the 3/8" hole on mine is 2 3/4". There is I H Co. 790 inside my unit. Help!

Handle for casement window in condo. Located on bottom right side. Window has 3 panels that open from top to bottom.

hi need to replace several mechanisms, of course no manufacture part number 3/8 pin connection on arm, arm pin hole centers are 2 7/8 , mounting screw hole centers are for height 5 1/4,and 7/16 centers and 1 3/16 centers for the last set of holes. Hopefullly my info isn't to confusing ... (cont.)

Hello. I am looking for the window operators in the attached pictures please. I need both left and right side operators. Can you assist pls? Thank you

Hello, I need to replace several of these window cranks in my home. Can you help me find the correct replacement? Thanks