Viewing all customer Discussions for:

26-241 Pivot Bar, 3"

Pivot Pin Part # DHPB-90I am looking for this part for our windows. Would you have this part, if so what is the cost and do you ship to Canada

Good Morning! I am sending this in hopes you can help me with these window parts. I will be sending one more email with more pictures also.The clip on the top right side of the window is also broke ( these are pictures of the left which is ok, and the right side which is broke) . And of course the ... (cont.)

Hi Tom, I am sending more pictutes, I had to do it in more than one upload because it only allow. me to attach 3 pic per upload.The lenght of the balace is 34 in x 1/2 x 1/2 Please let me know if you need more info.Kind regards Mike

Looking for 10 to 20 pivot rods that have a defect where they break at the screw hole (closest to edge of window). Also there is the occasional break of the pivot piece (other picture) where I should get a few as well. lease let me know asap.

Hi Swisco, Looking for a replacement for this part. The part is made of metal and is 2-1/2" long. It has one hole that is 1-1/8" from the straight edge. The numbers 1441-1 are inscribed on it. Part came from a vinyl double-hung window and fits in a in a locking shoe. Thank you!

Once again, I have broken the pivot bars on my AK in 550 double hung windows. As my local distributor has gone out of business, I should probably get several of these to have on hand as I seem to break at least one every year when cleaning the windows. Would you have a replacement item? ... (cont.)

Hi: Can you tell me which pivot shoes and bars I need to order for replacement on my Acan windows (installed 2007)? I have some 26-241 in my cart right now (along with 30 latches because the old ones all started disintegrating), but I am not sure it is correct, or which shoes I need. Also, can yo ... (cont.)

The windows are of an unknown manufacturer, building was occupied in 2002. I found these parts for the windows but need more as the parts on the windows are breaking. These parts are attached to the lower corners of the windows and assist in raising the windows form their lowest position. They al ... (cont.)

I am requesting assistance in identifying replacement parts (channel balance, pivot block, and pivot bar) for a double-hung window. The window was made by "Timeline Vinyl Products" (which is now out of business) and was installed in 1997. The lower sash of the window measures 37.25? wide x 29? tal ... (cont.)

I would like to replace the window hardware on my park home. They are tilt in style, bottom windows only and top window is fixed. I searched but can't find the manufacturer of the windows so I hope you can help. I've attached pictures of the shoe and balance hardware. The original balance hardwar ... (cont.)

Broken hardware piece at bottom of sliding double hung window. Right hand side. Photos attached. Thanks.

Trying to ID this pivot bar. Looks like a 26021, but mine has two wings on end (one is broken off). # on back is 23145

I have a window where both bottom pins are broken off. I need 2 pieces like the picture attached

Hello: I am trying to find some broken replacement parts for my Harvey windows. I have attached photos that I hope will help. If you have any questions, please let me know. Thank you in advance for your assistance. Debbie

This piece was bent and broke when I tried to straighten it. It is at the bottom of a single hung window and slides into the pivot foot. Also need to replace the spring on these "carefree" windows

The channel that the wedge or shoe rests in (see item C-Bottom), is approximately 1 3/8". The bottom sash is 29 7/8" by 32 3/8" wide. Frame opening is 32 1/2". The channel that both sashes sit in is 58 1/4" high.

Need a lh and rh tilt latch. Right hand tilt rod? Or tilt pin?

Looking for the bars that mount to the bottom of the double hung sash.

I am unable to find this pivot Bar with the holes in the correct position. Is there a slotted one available that will work? The closest I can find on your website is Product-Code 26-454. All dimensions are right but the holes are in the wrong position.

3 inches long 7/8 inches wide numbers on top 501081