Viewing all customer Discussions for:

26-244 Tilt Window Latch, Right Hand

Please see photo

I need the appropriate coil for a simonton double hung window

Hi there, Please give me the those three parts code/product number so I can order. Thanks! Amy

We need to replace these. Windows were installed in 1998. Not sure which item would be the replacement. Hope you can help us out.

I have a double hung window 33"x47" and the top section has a broken surface mounted tilt latch and the bar that goes into the valance is also looks bent. the Valance spring also appears to be broken. Both are on the left side when facing window from the inside. I would like replace both bars and bo ... (cont.)

Looking for several replacement block and tackle assemblies for tilt-in windows. The rod measures 27 1/4" long and the spring is 13 3/4" long. These are older windows and I can't find a manufacturer identified. Inside of the window frame is the following: AGC 10 IGCC/IGMA E2190 '14 stamped into the ... (cont.)

Trying to determine replacement part for the Ply Gem window latch. The house was built 2008 by Ryan homes. The numbers on the back: 10H, 075, PAT.#5,139,291Hope you can help. Thanks

Looking for the damaged parts in the picture, this is what my contractor has sent me to help locate them.

I need some parts for my 20-year-old windows from an unknown manufacturers. The lower pane has latches at each side on top. They are plastic and 2.5" long with a sliding tab which hold the top of the window from tilting in.The pictures aren't great but hopefully will help.Louis

These latches are from Dove Aluminum Windows.(no longer in business) it was their 2000 line. That was their best window

Hello need the following: note this is for Marvin windows 2 of the pivot shoes part number is seen on one of the photos 2 spiral balance (see pictures) 28.5" long 2 tilt sashes ( see pictures) 2 replacement latches and replacement bases Thanks, Todd

Hello. I need replacement window latches, but I cannot tell if I need 25-244 and 26-243 or 26-419 or 26-420. I cannot figure out how to ascertain the 3/8 versus 3/16. The dimensions of the latch ar 2 5/8 and 11/16. Thank you.

Hi I need help with this what latch can I use for tilted windows, Im using a b24 balance on my windows Thank you

Hello, I am trying to locate replacement tilt window latches for my Windows. The top plate is 2 5/8" long, the top plate is 5/8" wide, the bottom side is 1/2" wide, and is 3/8" deep. The problem I have found is that most replacements are not flat on the sides and therefore won't slide into the win ... (cont.)

Good Morning, Please see enclosed photos. I need 4 clips and 4 of the post things that fit into the glide mechanism.

Hello! Could you tell me how I should choose the correct window tilt latch to replace the broken one? Thank you!

I need to replace this left hand tilt lock on my PGT window. The tilt locks I have found on your website do not have the hooked tongue, so I'm hoping you can recommend a replacement.

Dimensions in pics. Retaining channel is 9/16". (On window to slide into). Window American Craftsman. Silver Line 50 Series SH. Anderson? 35 3/8" x 59 1/4". #'s on window 8002344228 21554964.i. (i or a 1) CCL # 440-H-020 NFRC SIL-N-3-0412-0000 Left Hand looking out from house interior ... (cont.)

Hi these Plygem double hung Type 1000 DH windows were produced in 2011 looking for replacement surface mounted window tilt latches approx dimensions 2 5/8 by 5/8 I can't tell how deep they are. Also needing new coil balances as shown in the pictures. The numbers on the white cover are 5 365 638 and ... (cont.)

Tilt latch is broken on one side. It just slides into edge of window. No screws. Has a number in the back FAS10015