Viewing all customer Discussions for:

82-080 Mortise Style Handle Set, 4-15/16"

I need to replace this handle for my large Milgard slider. The part is actually broken son it is not staying on the door.

Pics attached of the sliding door lock which I would like to repair or replace. Screw holes on the front of the lock are 6-3/8" apart and in the center is the square hole for the latch. There are 2 hinges that pop out when the latched is pressed down. Screw holes on the side of the lock are 5" part ... (cont.)

Hello, In need of a replacement handle. Manufacturer is believed to be Anlin window. Thank you

My sliding glass door handle does not latch anymore. Can you sell me a replacement?

I have been trying to replace this handle. The screw holes are both broken.

I need a replacement handle for the interior of my glass door. If I have to buy the whole assembly, I will. However, a handle is all thats needed. Pic included. I've noticed the description states a door thickness of 1 3/8. My door is 2". Can someone help? I've purchased two handles that were wrong ... (cont.)

Plate inside door handle broke and I need to replace it.

Would you kindly help me identify the parts? The handle broke from its metal plate and there are no part numbers. The parts were made in New Zealand. The outside handle is curvy. The metal plate the outside handle is secured to is about 6 1/2 inches tall. The inside handle is a little over 6 1/ ... (cont.)

Patio sliding glass door, lock and handle broke. Great difficulty finding replacement part. Do not need the same thing just a lock and handle that will fit into the predrilled holes on the door. Thank you so much for any help you can give.Terry

Could these be your #82-030 and #82-080?

Attached are photos of patio door and handle. I do not have the mortise lock or of the strike plate or of the lever for the lock. I want to replace these and the handle itself. The opening for the mortise lock in the door is rounded at top and bottom and the screw holes above and below the openin ... (cont.)

The handle assembly is about 20 years old when the door was first installed over a period of time I'm pulling tugging pushing yanking kids mad people it finally gave way being that it's made of pot metal

Door is in locked position and the lock control does not release it so i cannot open the door.

Hi! Looking for a complete replacement for an Interlock patio door handle and lock. Hole spacing is roughly 5 inches.

Hello, I'm looking to change the lock on a sliding glass door lock. The inside of the handle has DR05-1530 stamped on it. Is it possible to get just the lock portion/cylinder? And are they keyed differently? I'd hate to buy one and have it be keyed the same as I'm switching the lock for a new tenant ... (cont.)

Hello! I have a slider Series 5200 Narrow Stile AAMA SGD-R20-96x96 I need a replacement handle and locks, rollers and the slider track. Can you send me the links to the replacements? I think I know what I need for the lock and handle, but not sure on the track and rollers.

I seek a similar replacement to DR05-1510 but am concerned part 82-108 does not provide the outer mounting screw holes. DR05-1510 has two outer mounting holes, two posts for horizontal bolt attachment, and an inner hole for the locking mechanism. 82-108 appears only to have the posts and inner hole ... (cont.)

I need the piece of the handle that has the stock # on it. It's what the interior handle screws into. I need just this piece, as you can see in the photo nut broke. Thanks

Sliding door handle, says made in new Zealand. Does not have any numbers or other markings other than the squiggles on front. Screw holes where it attaches to door are 4 15/16 inches center to center.

My living room has a 4-panel set of Certainteed sliding doors (Newcastle XT). The two middle panels move, and the two side panels are stationary. The two sliding panels lock in two ways: 1) mortise locks: These locks are doing fine. The left-hand sliding panel is equipped with three mortise locks, t ... (cont.)