Viewing all customer Discussions for:

82-080 Mortise Style Handle Set, 4-15/16"

I am looking for a replacement door handle for a PWG-M-144 New Castle XT

Model number SGD-R20- 96x96

The handle of the Milgard sliding door broke off. What part# or where can I find it? Thank you

I need an interior handle for a Legance 3 patio door

I have a clients door where it has this New Castle hardware as pictured above- and they want to add key operation to the exterior. What is the best part to convert? Thanks, JD

I am looking to replace the pictured handle hardware. As you can see, one of the screw casements on the base plate is sheared so it is impossible to get the handle to tighten down on the door frame. Please advise if you have suggestions? Thanks! John

What is,the difference between the 82-080 and 82-081?

I need the interior mechanism pictured above to make the lock work again on this sliding glass door. Marking on door sticker: Malibu Narrow Stile SD-R25-3048x2082 (120x82) What's it called? How do I identify it? Do you sell it. I have measurements if needed. THANKS! -Kenneth

Hi, I'm looking for the inside door mounting plate for a Milgard sliding glass door. The part number may be 14348

The handle says Interlock on the bottom. Please see the pictures for more detail. The handle is fine but the base that connects to the handle and door is broken. The housings that support the screws cracked. You can see the broken housings in the file that ends in 174515.

Could you tell me the part # and price for the handle insert on the right. Thanks DR05-1510

Hi! I have a replacement lock and handle for a sliding glass door that was sent to me by the company since it was still under warranty. The problem is, it came without any hardware to install it and the company (Pella, who now owns the former Viking manufacturer of the door) says they don't hav ... (cont.)

This is a handle from a Harvey Vinyl Sliding Patio Door. The markings on the glass of the door reads: G hercute CAN/CCSB -12M 16CFR1201 C11 7-97 1-2009 1 8 U Thank you so much for your help!

Hello, Can't find a maker name on door. Handle is stamped Made in New Zealand=. Holes are 4 15/16" O.C. Got anything that will work ? thanks, bill

This info is etched on the glass, G hercute CAN/CCSB -12M 16CFR1201 C11 7-97 1-2009 1 8 U Please advise ho to proceed

Hello, I am looking to replace a handle and lock set for a Legance 3 patio door TYPE: DPSG, CODE: TRI-K-36 with the following measurements: Outside: 0 1/2''' Inside: 7 1/2'''

Please help us in finding a replacement part for this handle. It was new in 2005 on a builder home, so we have no idea where it came from. No i.d tags or markings on door itself? it measures 6 1/2 inches in overall length and screw holes are 5". Any help will be appreciated. Thank you, John ... (cont.)

I am looking for a replacement two hook mortise lock assembly for a glass sliding door. There are no labels or stickers to identify the manufacturer. The top and bottom door handle holes are 4 15/16" apart. With the outer plate on the mortise lock assembly, the overall height is 9". The only part nu ... (cont.)

I need a new latch system and it looks like you have a couple different double latch ones. How do I know which one to pick? My door will Not open and I am really waiting on your response to figure out which latch system and handle to buy. Do you mind getting back to me as soon as possible? It's 7 ... (cont.)

Hi, I have a sliding patio door, that requires a lot of force to toggle the lock - so far my troubleshooting has indicated a mismatch between the lock-side and strike-place/receiver side (sorry, I don't know what these are called, but have included the photos). Basically, exactly at the center of ... (cont.)