Viewing all customer Discussions for:

15-004 Winged Channel Balance Shoe, 1-3/32" Depth

I need a replacement window channel, I will attach photo's. The measurements are 1/2" wide X 34" metal to metal,long with a spring inside Thank you Dick

Please help with identity for replacement. Stamp is "26 4 CALDWELL IM" Lenght of metal channel is 27", Width is 1/2" inside. I am attatching photo of ends. Thank you..Dennis

I'm needing to replace two (2) channel balances w/ top/bottom guides however, I cannot determine which ones I need based on the pictures or item numbers listed. I'm looking to replace a rolled-edge channel guide; 30 inches in length with "293" and "AJ" stamped on it (they are slightly seperated fro ... (cont.)

I have Kinco make single hung Aluminium Windows in my Highland home in Tampa. Some of the channel balancers have gone bad due to breakage of plastic top and bottom clips. I tried to find out suitable replacement balancers from your online catalogue but not sure of the match. Details of my e ... (cont.)

Greetings, I took several pics of my channel counter balancers, probably more than needed. I also looked at your web page and beleive this is a series 390. So you know, this is 1/2 wide and 27" long. The number stamped on it is 2630. Can you please help me confirm the correct series number f ... (cont.)

I have a Nu Air non tilt window, single hung that has a damaged channel sash balance. The damaged part has the following ID Number: #29 5 fw cmc 10 Can you help me identify and order the correct replacement part?

I'm looking at the stamp on my balance it does not say the full 4 numbers, it states "21 2" then after the "2" vertically it has 3 letter stamp "B.S.I.", then horizontally (same direction as "21 2" after the "B.S.I.") it's followed by a NG. I'm convinced the part I need is a 22" s380. Is there any ... (cont.)

Hi- Trying to locate a replacement balance (non tilt, 1/2" channel)used in a window built by NuAir in Tampa Fl. (they are out of business) I am having trouble doing an ID from the pictures on your web site. Can I send you pictures of what I have? Also, the balance is lifting insulated glass and wo ... (cont.)

Is the window missing the balances the same type and brand of your other window? Attach some photos of your current channel balance system to your reply post.

I ordered some series 351 channel balances based on your recommendation that many customers find that they work for GapCo windows. They DO work, but they are not exactly correct - the window has some left-right play as it goes up and down. I was reluctant to actual take out the old balances until I ... (cont.)

The channel balances in my windows appear to have a 15-004 shoe and a 19-005 top. (1/2" wide balance, non-tilt aluminum window) Do you have anything compatable? I need... one pair for a 16" 1520 BSI one pair for a 22" 2130 BSI two pair for a 28" 2730 BSI

I have a Kinco Window that needs the balance Cart. replaced. The window is approx 6-7yr old. It has the markings: 29 3 EX CMC 11. The channel is 9/16 wide x 9/16 deep with hemmed edges and is exactly 30-in long. The top guide is similar to your 19-002 except that it has wings on the back li ... (cont.)

I am looking to replace a dozen window balances. I do not seem to be able to find a match on your web page. It appears to me that they have a 15-005 on one end and possibly a 19-005 on the other.Stamp: 2720 BSI

Hello, Does the whole Channel come comeplete with the "Cord" & "Terminal Clip" complete, as well as the upper a lower Top & Bottom Guide ? The Channel is stamped "2930" ~~Thank you for your help, best wishes, Joe