Viewing all customer Discussions for:

36-049 2-Bar Hinge Set, 14"

Truth serial number 31858 window crank casement opening left hand crank, window dislodged at top crank serial number 31858 window sash is13in long with two 7in arms and are dislodged. serial number on clip that fell off is 31865-B

I hope my photos will help you identify the correct replacement operator.

Hi there! Our whole house has New Castle Casement Windows by CertainTeed. I am needing replacement hinges for various size of windows. This is an example of what I am looking for.

I need 2 different operators, I think dyad and dual. Also the latches 2 different kinds , stud brackets and hinges(10" and 14").

I am looking for replacement parts for casement windows. I hope that you can help. The rail for the operator has is 14.5 inches and these are for windows with hinges on the right. The lower hinge for the left hinged window is stamped 32062, but I need hinges for the right hinged windows as well. Tha ... (cont.)

I need for the left and right hinge

Arm is 12 inch. Condo built in 1984 Left hinge

Hoping to find a replacement for the hinge in the picture. The results I found online don't match what's in the photo, even though they seem to have the same part number. The one I currently have has a curved arm attached to the railing. Any help would be greatly appreciated.

Need help with part number for the 2 pictures below. 2 different size window

I need replacement hinges for a Truth casement window. House was built in 1986 and I suspect these windows were part of the original construction. I don't see any hinge hardware that has the dogleg angle to it as seen in the photos. Full window size is 34" width, but there are two windows in that sp ... (cont.)

I am in need of the external crank components for my Jeld-wen casement windows. I have multiple windows. They are all custom sized (four 35"w x 49"h; two 31" x 49"h; two 26"w x 47"h; two 34.25"w x 46.5"h) the parts needed are pictured as they are all starting to rust. And two windows are not operati ... (cont.)

Hi, I'm looking for the correct part to replace on this bay window with 18in casement. The crank arm pin rivit rusted. Thank you, Brian

I need parts for some Milgard windows - hinges and connect arms, and brackets. The part numbers for the hinges/connect arms is "HA0438TK 64XX/5421 TRK & SLDR ASS'Y EG". I also need the brackets on the vertical inside of the windows. I've attached photos with red arrows or red lines pointing at w ... (cont.)

Hello, I am looking for casement window hinges for bottom and top and for both right and left swinging casement windows. I need two pairs of right swinging and two pairs of left swinging (total of 4 windows). The manufacturer is out of business. The brand is Eagle View Windows & Doors in Jacksonvill ... (cont.)

The subject linkage is from the left side of my casement frame. The part that slides into the track has been damaged (the plastic has broken off). The window was made by Hurd Millwork Co.

Looking for these hinges

Good evening, I need two operators same style but one each for a right and left opening window. See pics above and let me know if there is anything else that is needed. Thank you, Gary

This part is on a 50-year-old Pella window. It will roll one way but will not let me roll it back.

Approximately 20" wide casement. Looking for both upper and lower arms.

My customer has 4 30"/60" casement windows, the hinge pieces on the bottom are rusted out. The hinge piece consists of a track the screws to the jamb 1 arm that clips to a bracket mounted on the window. The main track is about 13" the arm is about 10" and the bracket on the window is about 5" . All ... (cont.)