Viewing all customer Discussions for:

32-039 Drawer Roller

I have a cabinet draw and looking for a replacement wheel. The wheel is 3/4 by approx 1/8 to 1/4 wide

Hi,I hope you can help. I am restoring a vintage metal desk, made by steelacase.SpecsThe roller measures 1" od8/32 wideThe hole and desk mounting pin measure 8/32 also.I design/build and restore furniture for a living.Thank you!Tom K.

Good morning, Looking to replace just the wheel as the bearings and wheel came apart. Would part 32-039 work in your opinion as drawers are old and not worth a lot of effort to repair. Thank you and have a great morning. Kurt

How do you get the old wheel that is thrashed out of the rail? Mine has a metal axle. Thanks. Tennes

I need part 346DR for the right bottom back of drawer where the wheel fell off. The pictures are blurry but the number is definitely 346. I included a photo of the left side which has the wheel. Is this part still available?

I have St. Charles metal cabinets and I need to replace the nylon roller in one of the drawers. It measures 1 inch in diameter and is about 1/4 inch thick. Do you carry a replacement?

Good morning, I will have to get a count, but I need around 20 of these 1" drawer wheels to fix some metal cabinets in my office. They appear to be about 1 inch long as well. Thanks, Bill

Hello! I'm trying to replace some drawer rollers from some old steel kitchen cabinets. I just received part #32-096, and they are so close! Yet the axle is a little deeper than the original parts so they make the wheels stick out a tiny bit too much. The rest of the roller seems to fit pretty well, ... (cont.)

how do you punch it out.

When I powder coated these drawers I misplaced one of the rollers. The 1 1/8'' will not work. They are rescued from a demo.

I have exactly the same slide as here, and also need replacement wheels. I looked at 32-096, and they look like they would work with the exception of the 1/4 inch collar between the threads and wheel. These slides have this built in. Any chance that this can be removed or that (even better) there ... (cont.)

Looking for glide wheels for an old Anderson Hickey filing cabinet. The axle is 6/32 of an inch i diameter. The wheel itself is an inch in diameter and 3/8 of an inch thick. Thanks for your help.

The guy I bought the cabinet from told me they came out of a pharmacy. I purchased part 10-101 which is the right size 7/8" x 1/4" with the hole size of 3/8". I drilled out the bearing but the problem with the 10-101 is the center after I removed the bearings was thin and broke when I tried to put i ... (cont.)

Hello, I am trying to find some replacement rollers for 2 credenzas in my office. Your website has the closest thing I have seen. Can you help? Cole

It appears to be a 1" OD by 1/4+" wide with a 1/4" hole ID that does not go all the way through, thus keeping the wheel from moving too far to the outside and providing a slide to keep the drawer aligned. I think it is made of nylon or hard plastic.

Hi, do you know the width of the inside hole of 32-039? I saw that the lighter white part can be punched out. Do you know how difficult that would be? Is it meant to be disassembled by hand?

Need 2 of the plastic bushings for the center drawer. Need 2 wheels for the side drawers. Need 8 keepers for wheels mentioned above. Are the metal dividers for the drawers available? Thanks Joe

I need to replace drawer roller or ring for a steel drawer. The drawer faceplate is 30" wide and 6" high. The roller is a hair over 1" (28mm) outer diameter and exactly 1/4 inch deep. Photo a: Damaged nylon roller Photo b: Roller wheel without ring Photo c: Remaining roller

I need the wheel for a drawer

There are no markings of any kind. Drawers and this small bracket are plastic, probably 30 years old if I had to guess. The surface of the bracket where the runner rests appears to be approximately 1/5" wide. It sticks out from the wall about 1/2". There's a matching one on the other side of each dr ... (cont.)