Viewing all customer Discussions for:

32-039 Drawer Roller

Hello I am looking for replacement Rollers for the Drawers in my Steel Office Desk. They are actually a Plastic or Nylon Roller bearing that is riveted into the drawer into a hole on the rear sides of the drawer on both the left and right side. They fall out after time from the holes they are rivete ... (cont.)

Hello, Do you carry drawer slide rollers with the threaded axle that are 1", outside diameter? I see that you have 1-1/8". Thank you, Nancy

Dear Sirs Need two of these....see attachment The mounts are in the desk already. desk is a Anderson Hickes and these are for the center drawer........ roller is 1' dia X 3/8? w X 3/8? hole with push on cap part number please thank you

I had this desk powder coated and I did not remove the roller wheels for the drawers. They were 1 in D and 1/4 in thick with about a 3/8 bore I think. Do you have anything that work as a replacement? Thanks Ben

I need replacement parts for my metal desk drawer: 1 each 1-1/8" diameter x 1/4" wide flat wheel 3 each 1/4" diameter x 5/16" long rivet or post & screw assembly Thanks Scott

I have a 35 year old Steelcase desk in great condition, but just needs additional desk drawer roller wheels. They are plastic. See attached 2 photos. The wheel is approx 2.5 CM wide or 1 inch wide with a center hole of 1 CM wide or 12/32 or 3/8 of an inch. The roller wheel is stamped WL 101 N. ... (cont.)

Hi there. I've been looking all over to find a replacement roller for the drawer in my roll top desk. I don't need an axle as the post is still there and there's no hardware to remove that I can find. The other roller measures an inch. Can you guys help? Appreciate any direction you can ... (cont.)

Hello, I have some cabinet drawers that need replacement wheels. The cabinet maker is St. Charles and it was installed in 1964. The following are 2 photo of both sides of the wheel. They measure 1 inch. Thank you for your assistance, please let me know if you have any questions.

Looking for Rivet Axle type of roller wheels for flat file cabinet. 1" diameter, 1/4" thick, 1/2 deep. If no rivet type are available please include other options. Thank you Joel

Looking for replacements for a desk which i was told is obsolete. Let me know what you have that can work. 15/16" and 3/8" center hole.

I can't seem to find something similar to the rollers I have on my metal desk. These roller slide over a metal piece inside the desk and then fastened with the push pin. Here is a link from another discussion with a similar roller. Mine looks a little different, but has the same dimensions as t ... (cont.)

Hi: Looked at 3 pics of roller 32-039: How does it stay in the drawer hole? Also, regarding a different drawer roller 32-096: what's the diameter of that metal piece between the nylon wheel and the threaded piece. Thanks for any help. Nelson

I need some plastic rollers with the plug to keep the roller on the shaft. The roller OD 1 inch ID 3/8 inch wide 3/8 inch The roller retainer OD 3/8 inch ID 8/32 inch wide 3/8 inch Can you help me with these parts for this desk. I can not find any model on the desk

WHAT SIZE HOLE IS REQUIRED TO ACCEPT THIS ROLLER?

32-039 is ALMOST exactly what I need. The roller I have does not have the protruding axel (shown on the right side in the 3rd picture). The overall width dimension is 5/8". Do you make such a part?

I'm looking for some replacement rollers for drawers in a Steelcase credenza. I'll send some pictures of the credenza and the rollers. I don't know the model or year, I'm afraid. I need four, but would buy a few extra if you've got them! They are round, 3/4-inch in diameter and 5/16th wide with a ... (cont.)

If the axle is removed what is the diameter of the remaining hole?

Hello, I need to replace 7 rollers of my steelcase desk drawers. Dimensions: 1 inch diameter, inside hole 3/8, 1/4 thickness. Could it be that product code 32-039 is the right one? It looks like it may be right, but I would need it with just a hole in the middle, without the axle part. ... (cont.)

Looking for plastic wheel 1-1/16 Inch diameter and 3/16 inch wide. It's from a 1950s steel kitchen cabinets .

Need some of these rollers for desk drawer which are missing