Viewing all customer Discussions for:

33-206 Shoulder Bolt Washer

I attached some pictures with measurements of my existing operators. Several have stripped/broken and need to be replaced. The windows are about 16 years old and I don't see any manufacturer tags which makes finding a replacement operator that much harder. Looking for several LH and RH operators, ... (cont.)

It measures 6 inches tall and 7/8 inches wide.

Hello, I'm trying to find 7 replacement cranks for my windows. I just bought the house and it was built in 1953. The porch was enclosed after it was built. The cranks don't pull the windows shut anymore. Any idea as to what parts I need to buy? I was able to rig them to stay shut for now. Thanks s ... (cont.)

No manufacturers identification on handle. 5/14" center of top hole to center of bottom.

Need to replace this with screws . It originally had a rivet that my husband had to pop out to take it off.

Hello! I have ten of these windows that are showing their age. I've looked everywhere for any type of markings and I can't find any. I saw a video where a guy replaced similar windows on his Airstream and said the model number is usually on the lower left exterior, but mine has nothing. I need ... (cont.)

How can I repair this arm on my Nuprime window operator

Similar to the customer who posted back in sept. 2017, I am in need of a replacement for my 1717r awning crank. After taking all the dimensions I purchased your 39-025.... but it was a no go ( picture attached). I would greatly appreciate a call so that we can figure out which one I need to purchase ... (cont.)

Hello, My name is Chuck G and I ordered this part # 39-008 last February. The operator had a crank on the right hand side which was fine for that window. Now I need the same operator but with the crank on the left hand side. I don't know how to order this on your website and have already s ... (cont.)

Hello, trying to replace old window cranks for the church. Unsure of what type to replace with 39-252 or the 39-205. Both a look except for the measurements. I would like to send you a photo of the type we have. I would like to order 40 each for the church. I have a tax exempt number for the orderin ... (cont.)

Hello: This is one of the old operators I want to replace with the ones I recently purchased. I think the part # is the same as ones I purchased earlier but I see the new ones are different. I drilled the threads out on one window to try and make one new operator work. But d

I am replacing a LH Type II operator on a Pan Am window. Please see picture where the hole-to-hole arm length is 2 3/4

I need to replace this operator. All the ones I find online have slightly different dimensions. My crank arm link is only 1.875" center-to-center. The vertical height between the mounting holes is 5 1/4" and the horizontal distance is 1 1/8". Can you find this part for me?

Dear Sir/Madam, Attached are pictures of my 1950's awning operator (Dimensions - 5 7/8" high and 7/8" inches wide). One of three triple window awnings in our mud room. Please note the 7/8" width is very tight with the wall. I believe that the crank threading may have broken off at the end. ... (cont.)

I'm trying to find these operators. The top to bottom screw holes are 5-1/4" apart, center to center. The bottom screw holes are 1-3/8" apart, C to C, and the outer arm is flat, and 2-7/16" long.

is this part available?

Handle has following identifying numbers/letters: C-11 500-11 Crank Assembly has following identifying numbers/letters: Pat. No. 198 202 US 12. H.R. RD. 1963 CA I believe the manufacturer is Weathertight. The home was built in 1996.

I need to find the clear plastic connectors (bushings?)to be able to connect the crank with the window levers. If it matters the crank is 4 1/2".

I'm in need of 13 replacement cranks for my florida windows. The house was built in 1968(?). There are no visible markings on the windows. Hardware is 6" long with screw holes on the left.

Hi Swisco, Here are photos of what I am looking to replace/repair. Product 39-194 is close; all measurements correspond EXCEPT for the 3/8" hole (mine is 3/16). And as I mentioned- when all folded in, on mine the arms fill the casing. Thanks for your help!