Viewing all customer Discussions for:

15-014 Balance knife lock Shoe

The actual measure of the channel is 35 " 9/16" wide by 1/2"deep actual measurements. The stamp says Unique 34-C-30. I need at least 14 of these. I need 14 of these. The others are stamped 26-D-40. I need 10. The end clip is different than you off on this model please advise.

Hello this is Brian. I am shopping for two sets of block & tackle window lifters for some old vinal windows purchased through crestline. The glass sizes are 29"wide by 28"tall & 26"wide by 27"tall. It would take the one inch lifters in the black cap sets I think. This is the code found on the seal ... (cont.)

Hello,I have several windows that won't stay where I open them to. They can free fall. They are approximately 20 years old and have a blue plastic part (I think it is the clutch???) that is broken or the string going to them has broken. I see that marvin uses a new system. Is it possible to upgrade? ... (cont.)

In your installation video for seris 751 channel balance you show the plastic sash being removed. This the the cream colored dual channel sides that ghe channel balance slides into from top end. My question is...do you sell the plastic sash/sill part also? Because, to remove mine is difficult w ... (cont.)

These are on a tilt window and ribbed balances. Measure 29 inches long. Also measures 1/2 x 1/2. We ordered S751-29 thinking they were them but they are took big. They are stamped 28TG

Is it possible to "flex" guide open to remove and replace a 751 series channel balance? If so, I would rather not remove and replace wooden trim and not risk damaging it (I have 5 windows to fix). Thanks, Steve

Hello, I have a double hung wind where the outside balancers have had the pulley to spring interface break. I originally looked up and ordered 770 x 27" based on the fact that the channel is not ribbed. Now I see that the balancers I have are 751 but not ribbed. Channels I have: Markings ... (cont.)

I have double-hung windows. I'd like to replace the side channels. The side channels have channel balances (27"-30#) and the channel shoes are the 15-014. Are replacement side channels available? I didn't see them on the website

Dear Sir/Madam, A while ago I bought balancers for windows. I think they were 25" Series 751 Channel Balances. The other day at that same job one of the windows would not stay up. After inspection, I found the right side had the sharp point of balancer had damaged the actual runner and it has to be ... (cont.)

the pic attached is from my tilt window. The shoes were on bottom of window I tried to loosen and slide shoe up, but it popped out

i have several wood windows that don't stay up. im not sure how to take them apart to know what i need to replace to fix them.

I bought a bunch of 15-014 terminals and they seem to work just fine. I found a complete existing one and it matches your 15-197. The original ones havent held up very well. I need to order more and dont know witch I should order. The originals were eather a bad batch or bad design. The 15-014 wor ... (cont.)

I believe the S751-34 is the correct part I need, but wanted to confirm. Attached you can see what I have now. It is 34" long with a ribbed channel and stamped 33TG. It is out of a weather shield window. The shoe appears different, but looks like it would work. The dimensions on the shoe ar ... (cont.)

I have about 20 Semco double hung tip-out windows all with similar problems with the shoe. I found part # 15-014 that seems close but mine are a little less than 1" wide. (3/8" X 15/16") Any ideas?

Dear Sirs: I am looking for balance which is 25

Looking for replacement shoe for Bonneville sash installed about 10 years ago mark on balance says "(03/12) UNIQUE 27 HD" Black shoe width is 3/8 inch height is 1 3/16 inch Thanks

Hi I am looking for these parts to some older double hung tilt windows we have and can't find them. :0)

Hello. I am in need of some window channel balances. Attached are pictures of the scenario: Notice in "window_channel_top" that the channel spring is attached with a single screw. Also notice that the screw hole in "channel_spring_top" is not currently supported and in some cases has become di ... (cont.)

I am searching for balances to repair this window. There are two 25" balances per side. Will the Series 751 balance meet these requirements?

We have several broken parts the markings 30 XHD 26 XHD Do you have a compatible replacement part? If so, what is your part number and where can I get a picture of it and pricing we nee approximately 12ea 26's and 4ea 30's I think that the "shoe" (Photo "26 HD Mrvn Tlt Blnc Shoe") is you ... (cont.)