Viewing all customer Discussions for:

39-032 EntryGard Dual Arm Operator

Can you identify these specific parts? I need one for the left window, and one for the right window. Thanks.

I just bought a number of the biege 14 1/2" tracks, and they are not going to work. This is a simpler track, with a cutout in the bottom to allow the operator "wheel" to snap in place. Four #7 screw holes, and not much else to distinguish it. I need a dozen or so. Thanks!

I am looking to replace 3 window arm operators. Please let me know if you have them, and how much each will cost. The info. on the arms reads as follows: R30842 - This one opens the window to the left I need one. 51538A - This one opens it to the right - I need two.

I am looking for a truth brand dual arm window crank replacement I need about 4 of them. The long arm is 9-3/8" long and the short arm is 7-5/8" long. The base plate is 4-7/8" x 2-1/16". Can you please help me find these parts?

Hello my name is Jen, I am the office manager at Mitri Brothers General Contractors and Roofing. I am looking for the cranks in the pictures above. Please let me know if you can help! Thank you!

Does Sisco have a replacement product for the casement operator arm in the attached pictures?

Need help to find the proper cranks. They don't close anymore. I have to pull on the window while cranking it closed. Any help would be appreciated. Thanks.

I need a replacement part for the crank system (not the handle) for a Milgard casement window. Thanks.

My window crank stopped working. It's stripped or something. I added 3 pictures.1. The number 50471 stamped here really small.2.The whole part needed.3. 30851 is stamped on the arm.The arm swings out to the right when opening.

Require placement cranks. A right and left crank.

Hello Both sides of bow window broken. Cranks stripped, spins and mechanism won't work. Only way to open is to unlock and pull from outside. Need complete assemblies for right and left side. Thanks Tom

The part has "Truth 30744" on it. It has a round part that goes in the slider, while the recommended parts on your website have either a square or rectangular part. Can you tell me which arm set would replace the one in the picture?

hello, i need to replace the shown window crank

Hi, I'm trying to replace the window Operator the bolt's teeth in the second picture has snapped off and is stuck inside the third picture. The brand is by Allied Windows which has run out of business. Please let me know if you have this part. Thanks!

On the crank teeth shown in the second photo it says Made in the USA on the left and Truth on the right. The underside of the handle in the first photo says US patent 4,083,264 then Can. Patent 1979 on the lower left and 45012 on the lower right. The cranks no longer grip allowing one to open or c ... (cont.)

I need to replace a operator cover and handle. possible number of a 1413271242831CW. Thank You!

Good morning. The window is located in a ocean community home so rusty is an issue. I need left hand and right hand operators, tracks and hinges. Hinges for top and bottom please. It's a bay window that still has the glass sealed. Amy help is appreciated

Looking for milgard casement window operators parts number stamped on #40753 on long arm, #31538A on short arm. The subject windows are approximately 25 to 30 years old and The operators were worn out. Please quote, thank you, Tom

I have 2 casement windows, both about 20 years old, where the roller/bushing is popping out of the operator track when the arm is cranked out to approx. the center of the track. Do you think it is an issue with the bushing/roller - or something else? If the bushing, is that available by itself? (par ... (cont.)

Hello,I need a positive identification on the attached short arm casement window operators( 3 each right and 3 each left). And also need the stud bracket for a right and left window one of each 39-032 and 39-031.(for a standard window size)Thanks,Chris