Viewing all customer Discussions for:

Door & Window

i have 4 windows with no channel balance...window is 36? x 30?...double pane aluminum frame...only bottom slides up and down...total window is 72? tall...what channel balance do i need...thank you mike

Item Holds 1/8" Plate Glass In Interior/Exterior House Window FixedNo Markings Anywhere ...Trying To Help Out An Elderly Couple ...House Built 1990s South Florida

Hi,Trying to replace the vent latch locks for my vinyl replacement windows by the manufacturer certainteed (13 years ago). The measurements of the lower part of the latch (that goes into the window frame) are 2 3/8 inch length, 3/8 width and 1/2 depth. Obviously the top is a little larger 1/2 inch ... (cont.)

I ordered and received keeper Product Code: 89-041. It's comparable to the one that's broken, but too small. Below is a pic of the broken keeper with a ruler for scale. HELP!

Need 6 left 6 right. These fit in to the shoe on a double hung windows that tilt in words.

Need one set of these Window balance for a set of vinyl windows

they are broke, comes in 2 pieces, handle and lock device handle snaps into inside screen frame

I have been unable to find the manufacturer listed anywhere on the window. I need to pivot pins for the windows. I hope you can help me identify the manufacturer and parts I need.

Hello - I need to get a replacement bottom door seal strip for a Stanley door that goes from the laundry room to our enclosed garage. The door is 31 3/4" wide 79 1/4" tall with a double groove on the bottom edge 7/8" apart on is 1 7/8" wide and runs the entire width of the door. The bottom door seal ... (cont.)

I am looking for the attached slider/guide. The opening is 72" It is a Stanley door with the wheels on the bottom.

I need 6 window sash channel balances. It is for 3 single hung, 20lb windows. I need completely new balances for both sides of all 3 windows, so 6 balances. The original balance is 9/16" wide and 29" long (only measuring the metal part). I cannot identify the plastic pieces on the ends. ... (cont.)

Total length around 23inch. Actually inner grey part has been broken and that's why it's not holding the spring. If I can get that then I need that otherwise whole part. I ordered 23 inch 2220 part but it's body aluminum, is little bigger than what I have. Thinking about ordering 2210. But though ... (cont.)

Hello! I have some Masterview windows in my house - built in 1999 in Phoenix, AZ. I need some new rollers. It looks like your part #87-147. In my photos, there are two pieces - I think they originally were together, but the plastic broke and separated. (These two pieces were not originally toge ... (cont.)

Looking to purchase these parts.Can't find part numbers.Thank you,Joe

Welded Knight Casement from Northeast Building Products CorporationWant the replacement parts for the casement windows.

Please advise part numbers for left and right pivot bars that actually hold corner of sash together.Thank youBob

Hello: I am trying to find window balances and sash release parts for my single hung windows. They are insulated vinyl windows installed in 2000. There are not any identifying labels, names, numbers, etc... The balances in these windows are a spring type. There is a 1/4' by 34-1/4'" hollow fi ... (cont.)

This is a broken pivot bar from a double hung window in a hospital. We cannot find a manufacturer on the window

Can you please confirm whether the attached photos are of a series 377 balancer. Unfortunately, there are no markings/stampings on the hardware. These are for hurricane-proof windows in our South Florida condominium apartment. Thanks in advance for your assistance.

I opened a window a few days ago and one of the balances popped out. I'd like to order a replacement but am not 100% sure what to order. I have attached pictures of the balance. It measures 27" long and has a plain channel that is 9/16" wide. The numbers on the channel show 26-5 with a TA and BS ... (cont.)