Viewing all customer Discussions for:

Door & Window

What can be used in place of these original pieces?

Don't know if you can help me, I'm looking for replacement constant force balance springs to replace the OEM springs used in my window wall which have ~ a 3 year life before failure. They are installed in a double hung, double glazed window assembly with each sash being 32" high and 29" wide. Curr ... (cont.)

I have to replace both balances on a ANLIN window the model number on the sticker is H-R20-48X96. Would the part S140-7 work for me as well? Are these hard to replace? I have replaced some window pins before on other windows in my house. Thanks for any help you can give me, scott- ... (cont.)

Hello, Can you please help me identify which window balance guide this is on your site? I couldn?t seem to find it. This is for a single hung window that can tilt in. Thank you for your help! Tom

The brand name is Larson on the little piece in the middle of the last picture. The last second picture is one broke and is needed to be replaced. Thanks.

number posted on side 1513 HC BSI. Want to make sure I get the right ones. I also need the clips that hold the balance in place on the top, I broke one when I was removing them. The balance is 16 inches long. Thanks for your help Jeffrey

Hi. I'm looking for a replacement pin for an older metal bifold door. The attached picture is the pin that is broken and keeps getting stuck in the channel. The pin length is 5", cap is 3/8" diameter, pin seems to be 1/4" diameter. Thank you for any help you can provide.

Can you determine if you offer this broken top guide?

Looking to replace an operator. The 39-025 is close. Except 1 1/8 between lower holes. Arm is 2 3/8 between pivot and hole. Also, top hole is slightly off center to the outside. Manufacturer is unknown.

Your part # 55-192 - having a devil of a time putting in bottom seal of window. Any crafty ideas like a feeler gauge - or fancy method to slide it in ??

I have a Cole Sewell storm door with registration number 09309894545 0079 and the door handle and mechanism is no longer working. Can I get a replacement handle? Please advise. Thanks. I can install the replacement if it is available.

I am looking for the equivalent TRUTH brand operator as the attached picture... I know it is from TRUTH hardware but have no other identification marks. Thank you.

Size 29 lenth9/16 wiseThey don?t have any numbers or markings on them.We need 14 of these.

Trying to figure out which series # will be the proper replacement for broken coiled balance springs for my windows. Springs on both sides have snapped. The pivot shoe # reads A186160 if that helps. Can you please help me ~ thank you!

Looking to repair myself but need the proper part. Need at least 3 of these, maybe 4.

Hello,I couldn't find the make and part number for it.Please help to identify this lock.This part from end to end is 4 inches.The body is 3 1/4 inches Thank you

I am looking for replacement block and tackle balances for older WeatherShield double hung windows. They are circa 1992 windows. Printed on a replacement that fits is the following 32.25-4 JE5 CMC.

My original faceplate does not have the same dimensions on it. The mortise lock itself will work if i have the right face plate. I purchased the 82-239 and i need the right plate to be able to install in my door. It is the same dimensions as my old lock just the screw hole placement is differentcon ... (cont.)

Our house was built in 1999 and about the only information I have is that the windows are Patriot brand. I need several latches and pivot pins for for these tilt-in windows. Pictures are attached but by my measure the latches are 2 5/8?L X 3/4?W 1/2?D and the pivot pins are 1 5/8?L X 1/4?W X appro ... (cont.)

Hi, This pivot shoe measures same as your 15-178. 2 1/8" high; 1 1/4" wide and 17/32"thick across main body but is 9/16" deep at the brake. However, this brake is white while your 15/178 is brown. Is the 15-178 the correct pivot shoe? Thanks, John