Viewing all customer Discussions for:

Door & Window

The spring in door is bad and want to replace the entire door and latch. Where can I get Swing latch assembly?

Dear Sir/Madam, Attached are pictures of my 1950's awning operator (Dimensions - 5 7/8" high and 7/8" inches wide). One of three triple window awnings in our mud room. Please note the 7/8" width is very tight with the wall. I believe that the crank threading may have broken off at the end. ... (cont.)

Request to order door latch and secondary security latch

Centerline between screws is 1". Do you have them?

Im wondering how much a aluminum window weighs. I need to buy new spiral balances for one of my windows. It is a tilt window. measures roughly 35.75" X 53.25". Any thoughts on what tip color I should go with? I know I need a balance that is 3/8" diameter and 28" long but my current balance does not ... (cont.)

We are in need of a replacement striker plate for the handle and lock. It is a Weight brand in a larso n storm door.

Please confirm that product code # 82-238 is the correct part to replace the part shown in the picture.

Hi I need to replace these rollers. Can you point me towards the spare parts? Also am I correct in thinking to get to old rollers out I need to take off the vertical part of the slider and knock the rollers out of the open end? Regards Ray

Need four of these!

Hi I need 2 left and 2 right side casement for Andersen windows, the product code is 7022. Do you have it in white or can I use a similar one that works with the old model?

I'm trying to find these operators. The top to bottom screw holes are 5-1/4" apart, center to center. The bottom screw holes are 1-3/8" apart, C to C, and the outer arm is flat, and 2-7/16" long.

hello- i moved into a home built in 1960s-think doors are orginal but not sure. would like to change handles to more modern look. I can't find any identifying marks on doors so no idea who makes them. The handle styles are 2 different styles and very old and worn looking. Any thoughts on what I can ... (cont.)

I tried your single wheel roller, the 81-132. But those nubs on the side make the roller too wide for my door. Your 81-019 looked promising (no nubs sticking out), but there's that black post sticking out the side. That might cause the same problem.

on the bottom of piece it says pat. no. d-212-686. it's from an andersen window, at least that's what the customer said, although the patent comes up as amerock.

I'm trying to find a cover for a pivot bar that broke. I'm unable to find a manufacture name. Only a tag that I think was the contractor's order information. See attached photos.

Hi there, My house was built in 1991 with Alcan windows in whole house with some broken Glazing Strips, Sash Guides and channel balance. 1. I took one balance out and measured the metal part, its length is 35 inches (window height is 37 inches), with part number showed as b 3420; and other balan ... (cont.)

I can't find an exact replacement on your site. No brand name on the window. Uses a 28" long, 3/8" diameter, yellow/orange tip sprial ballance. Shoe measures 1/2" thick 1" wide 2-1/8" tall. Window is approx 15 years old. All measurements are approx using a tape measure. Thanks for your help ... (cont.)

Ordered 39-025 to see if it would work with window even though final arm was about 3/6" short. Didn't work. Mounting holes lined up but window wouldn't fully close due to shorter arm. Also, some vinyl trim around windows is dried out and cracked so I have included a picture of that as well. Any h ... (cont.)

I am missing the handles on these 3 mechanisms. Looking inside, there is a gear to the side. No visible markings on mechanism. Windows are closed and I'm not sure how to remove the mechanism if I need to replace the entire mechanism. Do you have replacement handles? Your help and advise would be ... (cont.)

I am looking for glazing and window tilt locks I do not have any other information on these windows, there are no numbers on the parts or on the tops of the windows. The size is 3/4" and the small leg is 1/2"