Viewing all customer Discussions for:

Door & Window

Good afternoon, I am looking to buy replacement window rollers for my home and have not found the correct fit for my windows. Ive tried everwhere with no luck. I was hoping Swisco can help. Attached are the pictures of the original rollers. Pictures of it installed and uninstalled with measure ... (cont.)

Measures 1/2" wide and stamped 2130.

also need Right & Left closure locks.

I am in need of balances for my windows. Unfortunately they are different sizes,so I would like to start with this one. It measures 9/16 in width x29" long. The stamp number is 2850 CBSI. I am attaching several pictures to help identify my balances. I also need a latch as pictured and weather strip ... (cont.)

These casement windows are from 2003 and appear to be American Craftsman. I now have five broken locks and can't find this handle anywhere. HELP!!!

I'm inquiring about tightening the springs on my vinyl windows. I assume that I would need the 75-006 tool for this.The rods on the window are 25 inches with a red tip at the end and I think about 5/8 inch in diameter as seen in the attached picture.the shoe is shown also. Based on the shoe and ... (cont.)

I'm looking for a weather strip plug but for a 1-1/2" door

Need replacement latch for sliding glass door. Appears to be a Delta SL-3411 so far as we can tell. Do you have a compatible replacement part.

hi, can this replace a "push" lock--we have a single lock in the door-can we buy this and put the frame lock that comes w/it to replace our frame/jam lock and put this nice double handled 'handle' on our door - inside and out? thank you

Looking for a replacement top sash guide for my PGT window. Photo of good part attached. There are no markings on the part. I am unable to find this part on your web site. Can you assist in identifying this part? thanks, Mike

Trying to find a replacement. Window is approximately 8 years old. Unknown window manufacture. Looked every where on the window, unable to locate? Tilt window. If I did the measurements correctly. 36" long, 1/2 wide and 1/2 deep.

The Aluminum Channel Dimensions: Outside Width - 5/8" Inside Width - 1/2" Inside Height - 1 1/8" The Assembly slides into the channel. The Assembly Dimensions: Width - 1/2" Height - 1 1/32" Length - 1 7/8" Wheel Diameter: 2 1/4" Markings: Production Ent #6232

This is the handle I need 2108

I need a new cranking mechanism for my Norco window. The arm length is 12 inches long. Picture included.

Patented 1967 Can. Patent No. 3.237.238, however, my part does not match current image found on your web site for this Patent No. Home was built in 1973. No markings found on actual sliding patio screen door itself. Please see attached pics (sorry, a bit blurry)

Question: What patio door(s) does a Trust 31761 roller assembly fit?

I have a 13 year old house and I have no idea who the window manufacturer was. Here's a picture showing the model number? of a balance I removed from one of the windows. I have additional pictures of base and top plastic/nylon connectors if needed. I not yet weighed the sash, but I can if needed. ... (cont.)

Crestline via Menards doesn't have or carriy window hardware for widows that are older than 10 years old--or so I'm led to believe. I need to replace a left sliding lower window locking mechanism. The mechansim is mostly housed in the vertical casing with the actual cam-like lock/unlock lever on ... (cont.)

The latch is located on both top sides of tilt windows to keep the window from coming out. Several of my latched are broken on both sides. What is the replacement part.

Hi. I'm writing to you to inquire about what size series 500 spiral counterbalances I will need for the bottom sashes in three different non-tilt windows. These are not replacement parts. We will be outfitting these sashes with counterbalances for the first time. The overall measurement for the jam ... (cont.)