Viewing all customer Discussions for:

Door & Window

Do you carry the while plastic replacement roller for Milgard windows installed in the year 1986?

To whom it may concern: I trying to get full screens for upstairs windows. The window dimensions are approximately 51" x 24.5. The current half screens have lost the feathering that keep bugs out and they do not allow us to open windows from the top to prevent little kids from falling from the sec ... (cont.)

I have some older replacement windows (maybe even 20-30 years?), and one of them now has a broken pivot lock shoe (see attached photos) on the left interior window. There are two flat springs behind the lip of the channel to the left, and as you hopefully can see, the cam is broken on the left side. ... (cont.)

I need replacement Certainteed awning window crank mechanism. I am specifically looking for the mechanism to open and close. Please see the attached photos

Will your slide bolt 42-006 replace a ? It has a patent number on the part of D429 619. Thank you

I think that part I need is 39-035. Hope you can identify it with attached photos. Thanks Dmitry Patent

023632U.222040909

Width: 1/2 inch Length: 28 Marked : 2730S And one with same width but 22 inches long Marked: 2130Q Also my windows doesn't have the small locks on the side to release that window ,,,

Looks like your part # 55-164. Ruler should confirm this.

Hi - I have an anderson patio screen door and there is a plastic piece held in by a screw that stops the screen door from going too far (sort of a stopper). Do you carry this part? I can send a photo if needed. Thanks

We have found a product that is almost the same as the peice we are looking for there are just a few differences. The part I need is 5 1/4 inchs long from top to bottom bolt.. there are two bolt holes on the bottom that are 1 1/8 from center of bolt to.center of bolt..the extension arm is 2 3/8 inch ... (cont.)

Hi, Please help me identify the right replacement part. Here are the numbers and such-- 1521101 on arm Andersen 7227 on side arm High Perfomance CIG-3 3-95.6 IGCC CBA IGMAC 2.75" apart screws on operator probably installed in 1996 (at the same time as the other window that I am asking yo ... (cont.)

I'm looking for a set of pivot bars for American craftsman tilt-in window sash from home depot.I think # 08-2054. do you have a replacement for these?

I have decided that the correct channel balance I should get is the Series 351 - 28" but I don't know the stamp options. On the one I have now, it has printed on it '28 4 KR CALDWELL'. The sliding part of the window is 46" wide and 29" high. What would be the correct stamp option? Thanks! ... (cont.)

The picture of the glazing bead is from an aluminum window, 5'x4'6", single pane, fixed glass, with 1/4" tempered glass. I do not see any manufacturer's info on this window, but the second picture is the label from a similar frame in the same room. I think the glass in the window the label came from ... (cont.)

Does this come in a beige color?

i have 2 separate windows in need of balances. the one has 11600-2 C48 6#31 9-78 stamped on it. the other has 11600-2 E68 9#27 12-78 which balances are the exact replacement? also I'm replacing left and right balances on each of these windows so would each window have a pa

I have several BiltBest operators that are not working - crank is broken along shaft or just rotates w/o grabbing. Probably original from 1962-64. Photos attached. Thanks for your help.

We are trying to find snap in vinyl beading to replace around all our windows. This is what our vinyl looks like. What size would this be for ordering purposes?

We are looking for replacement coil balances they is a number 5 marked on the coil, but the plastic hardware looks more like your #4 The coil has an open end that we did not see on your website. As shown in one of the pictures one sets on top of the other but does not seem to be hooked together, ... (cont.)