Viewing all customer Discussions for:

Door & Window

Hi, I'm looking for help ordering replacement window balances for 6 windows. The stamp on the metal says 26 5 ew cmc 10. These are non-tilt windows.

I'm having a tough time identifying individual parts to replace my coil balance for my bathroom window. It seems your site forces individual part purchases instead of grouped parts. Help needed. The photos attached should provide most of the needed info. I don't know about weights but this window is ... (cont.)

Length: 28 in. Width: 9/16 in. Marking: 27 3 C H letters are in smaller font than numbers Bottom piece is broken and can't find the missing part.

Good morning folks, Looking to replace: 1-right side latch with thumb grip (Is the pin and spring included? Existing seem to be ok.) 1-right side stabilizer 6-stops Thank you, John

There are no numbers or any information.

Length 16", only marking found 15D need ends id'd so I can order replacements balances.

I am needing help locating a replacement window latch. I have tried in store and online. I am attaching pictures and patent information. I do not know the brand of window nor are there any markings that I can find. I need two RH and Two LH latches. Any information you could help me with would me a ... (cont.)

Hall Bath: Double Hung Pane 32 1/4 X 16 Master Bath: Double Hung Pane 24 1/4 X 20 Please tell me what sash balances that I should order to repair these two windows. The stampings on the ledges of the parts are shown in photo. There is an additional stamping that says 11600-17. These windows ... (cont.)

I measured the length of the balance spring tube from end to just before the blue color tip and it's 28.25". See attached photo. The sash weighs 22.5 lbs and the tube is 5/8". Should I order a 28" or 29" tube? Also do I have to order the charging tool or can I do by hand? Thanks, Lauren ... (cont.)

18 YEARS OLD - MEASURES 1/2" X 1/2"

The latches on the window locks are broken and i am looking for replacement locks to secure the windows. CHAMPION Windows

I need an Andersen sash balance for a Narrowline 3456 that was installed in 1986. It is a discontinued model. Here are the markings on the old balance: 1160017 and No 13 # 31 10 86 Thank you, Larry

Looking for two replacement springs lot a kinco window. See attached pictures

These casters have no numbers on them. They appear to be 2.5 inches by 2.5". The wheel itself looks to be 1.5" across. The plastic wheel is stamped with ACE and with LA, CA. The sliding mirror door was made by Charmac.

I need both the left and right balancers. It appears that the top plastic has wings while the shoe does not. It also appears that the shoe is a 15-001 (1-1/8") and the top is perhaps a 19-005. The channel is 1/2" x 28" long. Jack

I am looking to replace the handle and lock on an old sliding glass door. The door does not lock. I've attached photos and measurements. Photo 1 - It is approx. 6 1/2 inches from the top screw to the bottom screw on the handle that opens the door from the inside of the house. Photo 2 - It mea ... (cont.)

Greetings, I think I need 400 Spiral Balance Product Code S400-27, but hope you can confirm. Tube length is 27" Tip is red Diameter is 3/8 Pictures attached Thank you very much, Paul

I need a replacement lock for my sliding door handle. the screws seem to be 2 & 5/8 inches apart. The patent model says 3596954. Do you know where I can purchase this?

these windows look to be silverline maybe???(very old Style aluminum) Single sash double hung hinged on lift side Need balances for both sides string hooked onto frame window side held in place by latch on window top (same latch that holds window in)

I am looking to replace a pair of tilt latches, both left and right, on a white Allenco window. The part # on the latch is R 27. Do you carry these and what is the lead time.