Viewing all customer Discussions for:

Door & Window

Hello, I have a Stanley Door manufactured in 1985, and the only numbers I find on it are 970327B. I need to replace the weather stripping -- all of it. I've attached a few photos and would appreciate it if one of your experts could let me know what I need to order. Thank you! Best Regards ... (cont.)

Need a replacement handle for wood/vinyl crank out window. Dennis OP05-1509 on crank handle

DH Windows installed in the 1980s. Glass 33X24 (unit 3046?) the balance has E90 9#27 3 84 and 11600-17 markings. What balance do I need to order? Ron

We have a Andersen Window Sash balance stamped J58 5#23 5 80, It's from an Andersen window, house was built in 1979.Can you let me know the correct replacement part. Thank You

The spiral mechanism that connects with the gears that move and open the window is broken off on the end and will not close the window. It says 'Truth Entry Guard' but the piece that connects to the gear is angled and the replacement part #39-036 is not angled. The measurements are also different. ... (cont.)

I installed the 20-001 sash spring on the bottom of my bottom sash(es) because the cord sash opening on the top of the bottom sash was so large that I couldn't attach the nail (there was noting to pund it into). But now my windows are way too tight I can't opening them without extreme pressure. Wo ... (cont.)

Hi,I am looking for channel balances for my windows(as showed in the picture).I need your help because I couldn't find the right one with top and bottom guide.The icture showed is 33 inches and ido need the other one 27 inches loong with marked 32 4 FX CMC 11 The 33 inches long is marked 34 2HW CM ... (cont.)

Several of the pins, knobs and springs for the screens on our MW windows have been lost over a period of about 15 years usage. Would like to buy some replacement pins.

Does anyone know where I can find these wheels door is from the 60's

I need a few of these covers and handles to match as soon as possible. I will no tomorrow morning how many and if they are right or left. Please contact me as soon as possible. They are Pella parts and on the back it has 77bh and p-1274-200

My door handle broke on my sliding glass door. The handle is a DorWal with a #L120 located on the inside of the handle. The holes connecting the sides are 3.5" apart. I already ordered (1) 82-055K : Keyed Handle Set, Acorn......which turned out to be a close fit but not quite it. The interna ... (cont.)

The pivot bar on my window was badly rusted and when I tried to remove the sash the bar broke leaving a rusty end stuck in the pivot shoe. What I want to know is can the colored rotating part of the shoe be removed from the white sliding part. This might make it easier do pry or drill out the rust ... (cont.)

I want to find a spiral balance to replace the ones in the lower sashes of my non-tilt wood windows. The existing balances sit in a channel in the sides of the sash. They are attached to the frame of the window at the top of the sash. The existing balances are 29 1/4 inches long, not including t ... (cont.)

I need to know what replacement part I need for my window. Thank you for your time.

Please, could you help me to identify Sash Support Andersen Window Balance - c39 6#23 3-78 - these are the only markings I found on the sash box. House built in 1978.

I have an Andersen window sash balancer #11600-3 on patent number side and on cord side says #1600-2 d50 7#27 7 82. which one would replace this? thanks.

Hello, one of my window channel balances recently broke (the tension string). How do I go about ordering the correct one? There are no markings other than the numbers and letters listed below: 28.5 GX CMC 11 The metal part is about 28.5 inches and the width is 1/2". Thank you

Can you please tell me which sash balancer I need for the Anderson part number: P15 12#31 9 79 ??? Thanks, Rich J

Hi, I'm trying to get your opinion on a replacement roller for my acadia sliding doors. These rollers slip into the bottom of the door and don't really fasten in. I was able to pop both of them out to double check on their condition. The one number I was able to see 4178 stamped in one of the un ... (cont.)

Hey guys I want to make sure I order the right latch and lever for my door. There is no name on door. Please reply to my request on the right parts. I think it is latch # 82-218 and Lever # 82-106. Thank you, Dave G.