Viewing all customer Discussions for:

Door & Window

Hi As per the attached picture I need to replace the entire crank system for my casement windows. I have 6 to replace. Do you have ones similar to these. Thank you Jo Ann

double hung wooden windows. balancer # 11600-17; BE 199#31 2 87.Need both since lower sash slack on both sides, no uptake.

This window and hardware have no markings I could locate. The upper bar that attaches to the window is 13 1/2" with a two screw attachment bracket at each end. Each attachment bracket is 3" long with two screws holes and two connecting tabs. The short linkage arms are 6 1/2" long.. The longer ar ... (cont.)

What is the width of the top of the V section?

We need 20 of these. Can't find a part number. only number is a Pat No 4,850,078

sliding screen door rollers part #at.3716693

I need two Channel Balance for a non tilt window, width is 1/2" and length is 31" from just ends of metal case. Numbers and letters on metal case: 30 4 HV CMC 7. I have additional photos if you need to see more.

i need to replace the left and right balances on my parents wood double hung window. the numbers on the original balances are 11600-17 and H106233-88. can you tell me which replacement balances i need. i got the numbers off the balances that are on the window now.

There are no identifying marks on this part or the window itself. I have more pictures if needed.

Hello! We are looking for 4 more window balancers just like this one. We took this out of one of the existing windows. We've had bad luck with ordering parts online only to get them and have them be the wrong thing, so rather than just ordering a generic window balancer, I want to make sure it's exa ... (cont.)

Hi, I'm looking for a replacement crank handle. Can you help me identify the product? Thanks Sam

I'm searching for a Danvid tilt window latch. Attached is the picture of latch on the window. width - 15/16 inch length - 2 1/2 inches screws - end of screw to end of other screw - 1 1/2 inches 1st screw is 1 inch from end of latch edge Kaye Thank you for your help.

I have a left and right crank out windows with roto hardware both crank handles broke off with the shank still inside the housing,,,,,, My big question is what is the best way to get them out,,,,, and do you have the replacement cranks,,, they are white, I would call them male handles as the sh ... (cont.)

Need to replace a Milgard 33 " 1/2 " channel balance. Code on balance is 32 5 GW CMC 11. What balance of yours will work?

Hi, I am looking to find these replacement pins. The windows are approximately 30ish years old. I need 6 if possible. Thank you so much for helping! Lindsay

I have four of these Thermal gard cranks. The windows have double latches which open simultaneously (if that helps you identify the brand) All of the cranks are in need of replacement for one reason or another. My guess is 25 years old?

Hello, I have aluminum impact glass french doors that open outward to my back yard , I have an in-ground pooland I need to put some type of latch on those doors so if my grandson (2 years old) open the lock the latch will prevent him to open the door.I was looking at you product code 40-145. Can ... (cont.)

Attached is a picture of the bottom roller from my screen door. Will your 84-024 work? Dimensions are 2 1/2" hole, 1/12 height of the metal of the bottom of the screen door, 3/8 interior diameter of the hole. The roller has to be attached by a screw up from the bottom into a hole in a tab, not ... (cont.)

Do you have any sliding window sash locks with a 1" hole opening like the attached pictures? It's an old 1950's window with no markings or numbers on either the window or the lock itself.

Recently we have had some security issues with entry via sliding patio doors. I am looking for added security latches and other means of providing comfort for my family. Some neighbors have installed J-Hook latches but they are not very attractive. (FYI--the tracks are on the outside so the b ... (cont.)