Viewing all customer Discussions for:

Door & Window

Looking for a constant force balance coil system for a window track that looks to be about 1.25" wide.

can you explain how to attach 55-184 to the window grid and sash? dan

We recently purchased a house with single tilt windows. Some of the screens needs replaced. What we thought would be an easy removal of screens to replace them has us baffled. The upper corners of the screens has something like part number 95-186. We thought if you pulled on that the screen woul ... (cont.)

I have daylight between my sash and jamb on a vinyl replacement window. Is there hardware that can be purchased to install between the old window frame and the replacment so the window can be adjusted without removing molding. I would like to do minor adjustments with the changing seasons. ... (cont.)

I have an Alenco window, the channel balance is marked 2740 BMI. See attached pics. Can you tell me the correct part number to replace it? Thank you

I have a window channel balance that looks like it has a 19-005 top piece, and a 15-003 bottom piece, the metal part is 26 inches long, and has code 25-3 EA2 CMC 12 stamped on it. Can you please tell me which balance to buy?

Do they have both left handed corner and right handed corner For product 95-052 or just only one type?

the take out clips are "missing" (got disengaged) on both sides. the left side is off. the right side is normal for the channel balances. the window won't close all the way. the sash is stuck.

Hello, I think this part matches the parts on my moms aluminum windows on a Jose built in 1991. From what I read it sounds like many other people have had the same problem wth a derive alloy and the lock crumbles. I need to replace all the locks if the house and that will be about 29 of the part ... (cont.)

The existing part has K D J AL markings on it aproximate 5 inch hole to hole on housing about 2 1/4 inch on arm link. I can send photos if you supply email address and persons name I should send them to. I need 4 units along with screws and crank arms . Right hand

I have a channel balance for a non-tilting window with the following markings: 25 5 cx cmc 11 It is a 1/2 inch in width and 25 inches long. I have attached 4 photos which I hope will help you identify it. Thanks. -JK-

I have 2 windows that have counter balance problems. The channel balance falls from the window even though I followed the video. As I lift the window up- the channel balance falls. Do I need to change the whole part or just the guides w/ rivet parts. Please advise Thanks

It appears that 26-157 (RH) and 26-158 (LH)are the correct parts. These parts mention Better Bilt. Can they be used on Gapco window? Looks identical.

Between 82-102 and 82-101, how do I determine which one i need, also how do attach it to the frame as i currently don't have hardware for it.

I need to replace both balances and sash guides on a window I am repairing. The window is non-tilting, 1/2" balances, 29" long. The stamp reads, 28 3 CALDWELL LM. I am having trouble identifying the correct shoes and guides, so am sending along photographs. Your help would be greatly apprec ... (cont.)

The set screw that holds the handle to the shaft is stripped and unusable. Need new inside and outside handle and shaft. Three photos attached show: 1. Overview of lock mechanism. 2. Loose handle on door. 3. Loose handle by itself

Looking for the roller assy... see picture

andersen window 11600A-3

My rear door is a slider to the deck and the latch for the lock is missing. No names on the Door. The latch is 4"x5/8". The door is 1 5/8" wide. The latch from the slider only comes out of the door a small distance. The latch must fit within the opening in the slider part of the door to be able t ... (cont.)

We need help knowing if this deadbolt set (40-058) will fit our storm door. Here are our approximate measurements: Outside: Top 2 & 3/8" by 1 & 1/2" Bottom 4 3/8" by 1 & 1/2" Inside measurements: Top 2 & 1/2" by 1 & 1/8" Bottom 3 & 1/2" by 1 & 1/16" Thanks!