Viewing all customer Discussions for:

Door & Window

Hi; I got the replacement crank arm today and I can't see any way this part will fit. The part is 39-264 was supposed to be the replacement for the awning window. My operator has a few part numbers.C9400-1 on the top, F9400-8B on the bottom and 1521101 on the arm. The arm is 9" from the center of ... (cont.)

Need hardware for left and right casement window, sash is roughlyy 27 wide by 37. They are dark brown or dark bronze Thanks Tom

I have Bilt-Well double hung windows circa 1962. Bilt-Well is now Eagle & part of Andersen. They have plastic balance boxes with the number 79 stamped on the end and measure 8" long, 3 1/4" wide and 1" high. Can you tell me which Andersen balance would replace the old Bilt-Well one, or if not wha ... (cont.)

I am trying to see if this hardware comes with a top hinge or not. thank you for your response

Do you sell the window balance for the 2800 series Patriot double hung windows? I need to order a replacement so I can keep the top window form falling down when unlocked. Thanks.

Hello: I have 2 SilverLine sliding patio doors that need the handles replaced. I am hoping that you can confirm that your product 82-035 is the one I need before I purchase. I've attached two pictures hoping that you can see the opening for the lock mechanism, which only has one opening. Thank y ... (cont.)

Trying to determine required top and shoe connector hw for a 2730 balance. I have attached front and back photo's for these. Thanks, Tim

I want to order the replacement kit but I'm not sure I can install with some diagram or instruction. Could I view that befoer palcing an order?

Please identify.

I have single hung windows that I believe were manufactured by MI Windows and Door in the mid 90's. They have a mfg code of MTL-6. The balance spring has broken on some of them and I can't figure how to remove the spring after I remove the bottom window. I have removed all the screws holding the ... (cont.)

attachments show rollers I need to replace they are stamped DELMAR and P.E.

I am looking to replace my sliding glass door handle. The back plate for the internal lock that hols it inot position is missing along with the outside handle. The internal lock has a patent # 919213 patented 1975. I am enclosing pictures of what I have. It is surfacre mounted and the screw hol ... (cont.)

Need 2 each replacement balances for my Acorn window. Width is 1/2" and length is 35". Phil

I need to replace some spiral balances. My balance is a blue tip (900 series) but the length is 24 1/2 and the diameter at the blue tip is 1/2 inch which is a spring and not a tube.(Note image) My balance is a combination of spring and tube. The spring at the bottom is approx. 13" and blue tip to e ... (cont.)

I think I need an s380-26" I know the top plastic piece is right but the shoe is a little tough. I will send some pictures so you can identify it.

I need internal tilt window latches. they are 2-3/4 long X 3/4 wide X 5/16 tall. 3 photos attached. Thank you, Gil

I've looked at your site and from what I can see, you have two replacement exterior patio door handles available for a 3 15/16 inch hole-to-hole: the 82-042 (a solid one piece that is grabbed by the fingertips only) and the 82-044 (which appears to have a slightly raised rear portion for grabbing by ... (cont.)

I have a friend who just bought a home and 3 single hung window balance sets need to be replaced. The overall windows are 2 at 39x58 and 1 at 21x46. The balances are connected to the window with a sliding (kind of square) pin at the head of the operating sash. I do not believe these are tilt type wi ... (cont.)

The latch on our sun room door is broken and I would like to order a replacement. I am attaching pictures of the part that is broken. Thank you, Harry

I don't know the manufacture of the window, but the balance is printed as 14 4 jr caldwell.