Viewing all customer Discussions for:

Door & Window

Hi, I just ordered 16 Peachtree patio screen door rollers (84-028) to replace all 4 rollers on 4 separate screen doors. First, thanks for the prompt delivery. However, the screw that adjusts wheel height stripped in the plastic housing when minimal door pressure was applied. After a while sweating ... (cont.)

I order from you all regularly and did not find a part I need in your catalog, I did not know if you might have it. I am looking for a two wheeled roller set just like part# 81-018, however the one I need has flat nylon rollers. Thanks for your help, Brian

Hello! If your original stamp doesn't match any of ours, then the best way to determine which of our options will work is to weigh the window sash on a scale and pick from our weight chart.For your reference, the stamps available for the S751-25 are as follows: The 24R will carry a sash weight rang ... (cont.)

Take a look at the 39-013 and 39-014 for the same type of operator with a longer 13-1/2" arm. These operators are normally in stock and expedited shipping is available at checkout. Go to the following page to view our processing times: Shipping Policy

Take a look at SWISCO product codes 26-107 & 26-148. See if one of these vent locks match up to what you have.

You seem to be describing our spring clip 70-050. If this is not what you are trying to describe, please send images to us by attaching them to a reply post.

i think that the replacements i need are the 380 series but i am being asked for a stamped number. mine only have the printed information 22 4 ck caldwell and 13 4 bk caldwell and 13 4 lj caldwell these are 22 inch and 13 inch units

Is the 82-042 door pull available in white?

Good Morning, I recently purchased two of the 81-005 rollers to replace on my patio door. However there was no mounting screws included with the replacement rollers. I had already taken my patio door apart and destroyed the orginal screws that held the original rollers. Do you carry the mounting scr ... (cont.)

I am currently replacing spiral balances that keep breaking. They have a red tip, should I buy a stronger grade, Possibly blue tip, to stop them from breaking so easily? Please respond quickly as I need to have the apartment re-inspected after the repair, before tenant can move in. Thanks, Rob ... (cont.)

Not familiar with the Survivor line of windows. If you can't pick out the part on the SWISCO website, send us a photo of the pivot shoe you need and we will research it for you.

Both are bad. Do I need to change the rest of the supporint hardware. They look fine. 28322800J 28DH90920EAE17 which ever one works. Pivet shoe, etc

I'm trying to understand what you are doing. Are you replacing wooden frame screens, or are you replacing aluminum frame screens in wooden windows? If they are wooden frame screens, we do not have any plunger latch pins the length you need. Your best bet would be to go to an older Hardware store. Th ... (cont.)

On these sash guides (18-047), Is there only one screw hole opening? Also what is the width on the leg ? I am looking for a qty of 25 sets but not quite sure this is the exact match. thank you sherry , broadway glass and mirror

does the 83-019 handle work for any brand sliding screen door? i'm looking for the outside handle for my sliding screen door but i don't know what brand is the door?? do you know where i might find one? thanks

Hi, i have a inside door handle that is the same as the one in the photo in the first question on this page, you said it works with a shim, do you have the shim needed? Also, do i need to replace the striker or latch catch part that is mounted on the door frame? Thanks

I have Harvey Screen door's that have to have my wheels replaced. The part number 84-095 looks the same and the measurments seem to be the same but they are for a different manufacture. Can I use those to replace the one that need to be replaced? If I order them and I find out that they I cannot u ... (cont.)

Anderson use different rollers on different series doors through the years, the only true way to know is to remove the roller and look at it. If you get stuck trying to match the roller up, send pictures of it to us and we will see if we can identify it.

Yes, if it is a Series 770 with a channel length of 28" the stamp will normally start with 28. Please reply with detailed photos of the current balance, perhaps you have a different balance series.

Just trying to envision a type of screen that would work with this type of casement operator (39-077)... can you give me any advice regarding this? Thanks.