Discussions for Closet : SWISCO.com

the wheel is attached to a rectangular 2 walled metal with a part that slides up and down a track.

Installed a 8' door set about 15 years ago. Over the past few years the lower track has begun to curl upward away from the floor. This has occurred slowly and began to affect the ability of the doors (one in particular) to slide easily. At this point, one door cannot be opened without brute force ... (cont.)

Sliding mirror door

How do u adjust the sliding mirrored doors?? When they close, there is a gap at the top??

Mirrored sliding closet door adjustable top guide

Attached is a picture of the guide I need. I ordered a replacement door, but the new guides CW sent were inadequate.

LEIGH WARDROBE DOOR

An image is posted above. We need 9 sets of these rear by-pass hangers for our Bifold doors. We have 9 doors all together. Each door base 2 of these hangers with a wheel on it. We just can't figure out what exact part we need. Hope the photo helps. Jeanne

Charmac Inc top guide for sliding closet door 1987

Hi...I am looking for these nylon parts which have broken off. The doors are from 1987. I think they were originally to have mirrors, but we asked for them to be plain from same company. If you can help, I would appreciate it. Thanks Frances

These replaced my #17-4264y-000 and #00-5024 perfectly!

I used part #23-041 to replace Stanley part #17-4264y-000 (bottom) andI used part #23-222C to replace Stanley part #00-5024 (top) and they both are easy to install and are much better than the originals. Thanks for stocking these parts. I fixed my mother-in-laws closet doors and now I'm a hero!!!Bru ... (cont.)

I need 2 top pivot pins and one bottom pivot bracket.

I cannot find a manufacturer or other distinguishing features, but pic 006 is of a similar door showing a top pivot. The actual pivot rod that I need has a different pivot bracket, as shown in photo 007, where the 3/8 inch that goes into the bracket must be 1/4 inch. I also need one bottom bracket ... (cont.)

us patent 3.041.657

I ordered 8 of part 23-047. The roller is flat not round like the old one. Can help with the proper match or remedy ? Fits to tight in track. Brad

corner connector

Need corner connector to raise height of bifold door. Need the bolt that goes through the connector that pushes down bottom roller pivot. Does that bolt come with corner connector?

Roller that only has U.S. Pat. 4850145

I need to replace a roller that only has "U.S.Pat.4850145" and 23-028 was recommended in your blogs but my roller mount is on the opposite side. Is there another option?

Will wood door plastic guide cap (code 23-146) fit in track (code 23-454) ?

i want to order 6 48" bifold door tracks 7/16 pin (code 23-454) will your wood door plastic guide cap (code 23-146) slide freely in that track

Looking for replacement wheel assembly for Fleetwood mirrored closet door installed by California Closets in 1989

Hello, I hope you can help find replacement parts for broken wheels and wheel assemblies for Fleetwood mirrored sliding closet doors. They were installed by California Closets in 1989 and that company does not use Fleetwood closet doors any longer. I've uploaded photos with measurements. Than ... (cont.)

roller part # stanley 4011

I am not familiar with the given numbers but would be happy to research it for you. Please reply with detailed photos with measurements.

bifold pins and sliders

I have 8 of these bifold doors and on some of them, the upper and lower pins need sliders. RIght now the pins have no slider guides and are metal on metal. Attached are a few pictures of what the good sliders look like (upper and lower)and a shot or two of where the guides are missing. I am in need ... (cont.)

plastic, horizontal slide w/ spring in top track assembly

The attached photo was taken of the subject part in the top track assembly. It's about 2" long. What's it's name? Is it replaceable? Chris

Searching for 21073

I am chasing top roller for wardrobe door, the part i have has 21073 cox marked on it, although i am having trouble finding this part. Can you help me at all? Thanks Jas.

Sliding door hardware

Marking are: in a square box large L with B inside the L, us pat. 3.041.657, can.673.636(1963) Around hole with flat screw inside it says ."to lower door with arrow pointing down Both doors appear to have same size parts-1/2".

can't find this part

Hi.Need this wheeler.hope you have it

Bottome track

Our track is starting to roll and our doors are skipping track. Don't know any model or anything. its measure is 137"

Viewing all customer Discussions for: Closet

Viewing all customer Discussions for:
Closet