Viewing all customer Discussions for:

Other

I am looking for rollers for my patio door and I thought that I had found them in your 81-030 model. All the measurements were the same. However, I noticed that there was no groove as best shown in pictures 01 and 05. I didn't think too much about it until I went to reinstall the roller and I saw th ... (cont.)

I have two broken Channel balancers. The number is 26 4 AX CMC 7. See pictures I also need 2 sash guides for my Milgard window. Attached are some pictures also

3/4 L x 1/4 W x 3/8 H

Please advise me if you have a part that will replace my part.

Here are pics of an old broken balance. The only marking is J 29-3 I think the replacement is your S377 30" 2950? Cape Coral FL

I've been told my GA original 1985 aluminum windows are hard to raise due to channel balance. I unscrewed the top plate on one today, and almost got slammed in the face by the plate and screw under the spring pressue- cautionary tale! I am really on the fence about replacing these windows, but may ... (cont.)

The pin cap of our wooden bi-fold door has broken. Without one in place, the glide won't stay in the track. Our cap looks like a plastic top hat sitting on top of the metal pin. The metal pin is 2" tall, the top is 3/16" wide, the cap's opening is 1/4" wide, and the cap is 3/8" tall. ... (cont.)

Looking for the proper parts to replace multiple Pella operators - I can not find any indicator number. LW is stamped on the arm in attached picture

Pictured is the hardware used to attach the door to the door frame. The broken device is attached to the top of the door. The other device (not broken) is attached to the bottom of the door. These devices are used to suspend the door and to slide the door left or right. I believe the doors are manuf ... (cont.)

A sticker on the door says Cole Sewell Solid Saver registration Number SS 784521. I can open the door from the inside, but from the outside. The latch does not retract enough for me to open the door.

Please could you advise the part I need for my window. I have several windows where at this point the casing has become brittle. Many thanks. Michael

Are you able to identify this part? It is at my Dad's house, so if I need to go remove it I will. Just thought I would give it a try without taking it out. You guys have helped me before. Thank you so much! TerriAnn

I am trying to find the replacement for the pictured item. The picture is of a bottom rail with the pivot that is damaged. All I know is this is a Stanley door.

Good morning, Strangely, I am responsible for hundreds of windows over a decade and I've never had to replace one of these :). I have part 2340 off of a Pella window, but I have not found any pre-made ones. Depending on cost and shipping I will need a minimum of 1, potentially 2. Thank you Matt b ... (cont.)

Hi. This is a patio door roller assembly from a 1954 house, and it's probably original to the house. This one is broken, so I'd like to buy a pair of roller wheels to replace this one (and it's complement). Could you please advise me of a roller assembly that I could use to replace this one? The ... (cont.)

Cmech ,screw holes are 1 3/4 on centers

Want to replace all my kitchen cab. hinges. They are badly tarnished and no long stay closed. They are on Homecrest cabinets. I would like exact or close to exact replacements so I don't have redrill holes.

I am trying to find a matching weep hole cover. Interior width is 1.25", exterior is 1.5". I've included pics of the existing cover as well as the hole which is not square and about 1-5/16" wide. Thanks for your help.

anderson vinyl inside door lock broke. looking for replacement. attached are pix. also looking to replace rollers.

The 2 photos show the assemble and a closeup of the wheel. The wheel is riveted into the assembly. Are you able to locate 1 or 4 replacement assemblies or suggest a wheel I can replace the broken on with and re-rivet? I really hope you can help. Thank you