Viewing all customer Discussions for:

Other

The glass says Guardian but I don't see any other info on the door. Need 2 of these roller assemblies. .

The lock is double lock the locks are 7" center to center. The screw holes are 12" center to center. The handle screw holes are 12"center to center. One screw goes through the lock the other goes through the door.

Our customer has several windows with this hardware and needs replacements. They want the same style cranks

I had originally ordered 4 window balancers but the top was wrong and the bottom stops were too big for the channel. The first ones were 34" Series 795 Channel Balancers(S795-34) the pictures I am sending you are of the ones I need. They are 34B but slimmer channels. I would like to order 4 again. ... (cont.)

I have this dresser but all the plastics broke. I am having a hard time identifying the names or Part number.

Good morning, I am looking to order three of these operators. I have purchased 4 different ones, thinking one would work, but unfortunately, I was out of luck. Hoping you can HELP !!! BEELINE GLASS CO.

I need the attached window part. Can I get 2 of them?

The screw holes need to be 3/4 " apart . The holes on the part #26-466 are one inch apart

I cannot find the replacement for MEPLA Pie Cut Hinge for Lazy Susan 699.299.05.00, Clip-on. I also need the base plate for these.

Need a number of these per my discussion with your rep. please note the windows are 40 x 30 inches. the openings which contain the balances extend down the sides of the window and are approximately 25 inches in length. the balances themselves are cased in metal that twists around a ... (cont.)

Do you have something available to replace this interior sliding glass door handle? Harvey Windows responded to me stating this handle set has been discountinued. thanks, Don

Hello, I have 3 broken handles that need replacement. I found this product of yours, but I'm not sure if it will fit. https://www.swisco.com/Window-Lever-Operator/pd/Awning-Window-Replacement-Operators/39-069 The bracket on our window that holds the arms measures 3 inches across. The measurement ac ... (cont.)

I had ordered item number 38?079 from Swisco thinking that it was the right size. The clasp portion is longer than the sash lock keeper I'm replacing. The placement of the drill holes are correct. Do you think you may have the part that I'm looking for?

26HD 50 and a 26 16 window balance springs

Need to replace window balancers on Andersen window. numbers appear to be D20 8#31 8 84 11600-17

The side brackets that contain the two rollers measure 3.16 long x 1.06 high x .69 wide. There are two rollers that measure 1.25 diameter. The center distance between the two rollers measures 1.69. The rollers are steel with roller bearings inside. I did take photos on my phone but I am sending thi ... (cont.)

We have 2 windows that just the locks have broken where you open and close them. Just the lever broke. Any ideas or suggestions to replace 2 sets?Thank you in advance.Chrissy

This is the only marking I could find on these doors. The sweep is now missing and I need a replacement. I know it is not a "typical" sweep and I am looking for some help in determining which sweep will work for the door.

I have Sears Weather Beater vinyl windowsThis is the bottom window of a small kitchen window 16.75" H X 32.25" W See: Bottom window Barcode.pngThe bottom window has a broken plastic channel spring guide on the right side (from the inside). I think Left and Right may be the same if the coil is rev ... (cont.)

we have 19 loewen doug fir aluminum clad french casement windows that were taken out of their frames in a remodel. They open out. The rabbit goes all the way across the bottom of the window. Consequently we only have the hardware in the photo below and not the slider track portion. AmesburyTruth id ... (cont.)