Viewing all customer Discussions for:

39-107 Truth Hardware Operator Cover

need gray crank cover for casement window manf. around 2000

Hi, Do you have replacement parts for the referenced photos?

Hi, I'm looking for this casement operator. Can you help me cross reference it? I know it's made by Truth but it seems obsolete. I'm hoping I can find about 20 right and 20 left. Thanks Jeff H

This is the part number/name that I could obtain off the window hardware. Do you have these in stock? I need three of them and need to know how long it would take to get them shipped to me in Colorado Springs along with cost estimates. Thanks!

I am trying to locate some window hardware that will work for a casement window latch similar to the pictured. I've seen "weatherguard" as a brand name on some of the other windows but some have been replaced so i just need anything that will fit and work for this lock latch. I also need a crank ... (cont.)

I would like help with replacing the pictured crank handle with a smaller profile T-handle ( I need 3) so vertical blinds don't stack on top of current crank handle when lowered. I don't know spline size. Also, the sleeve that goes behind the locking latch, several windows are missing these. ... (cont.)

I have a jeld-wen casement window that is missing both handles and covers. Can you please advise what parts would fit this. I would like a folding handle if possible.

Looking for the replacement to the TRUTH hardware and the soft plastic foam filled seal I am holding. These are K/K Windows as seen on the crank cover. 25+ years old. I am reworking the wood but need seals to replace the old seals. HELP!

I believe I have an MW window and my cover around my hand crank has cracked. I have taped it in the picture. I would like to find out what part I need to replace this cracked cover. I don't know how hard it is to replace it myself, or whether I need a handyman to replace the cover. Thanks for ... (cont.)

We have three windows that are missing the cover and the Cranks the one window we have that has them I have attached a picture and it says enerpro on it. I'm hoping you can help me out and ship overnight Thanks Jackson H.

I'm thinking this is your part called Entrygard dual arm operator product code 39-032. It's truth hardware. Short arm has 20810 and 30842R on it. It's 4 inches and 7/16 long. The long arm is about 10 3/4. Do I need the short arm bracket as well? My problem is the window cranks out but not in. T ... (cont.)

numbers 30842r U.S. patent 4.241.541 CAN patent 350.432 pat. 1982 Ineed a new mechanism with handle and plastic cover to hide the mechanism.

Need to replace 2 casement window locks on a weathergard window. Also will need to replace a window crank or 2, and plastic cover (39-104; 39-107). Do you have locks for weathergard?

To Whom it May Concern, We have a K & K casement window that was installed 30 years ago and we need to replace the operator. The only number on the operator that I found was 40471. Any help you can provide would be greatly appreciated. Thank you for your time. Sincerely, Joe

It is a Truth brand, and the # I believe identifies it is 30744 although the following #'s were also on there, 40574 and 45108. The long arm is 9.5" in length. The crank to open'close is in the middle. Do you have a replacement for this? Sincerely, Sheila

I'm trying to find replacement hardware for 2 casement windows. The old mechanism's say Entry Guard and shows # 30744 on the arm. Can you ID from this? Please advise. Thank you, Tom

We need a replacement casement window crank. This crank is on the left hand side of a verically (left to right) opening window. The whole crank is not functioning and we would like to replace it. So we need more than a new handle, the whole mechanism to open the window. Do you have a replacement ... (cont.)

The gears on my cranks on some of my windows are worn out. Need new crank/operators. The plate for the operator says "Truth" Small control arm has # 20755

Do you know what is the brand?

Numbers on the part: 20755, 30842R, 40471, pat. #1982