Viewing all customer Discussions for:

39-114L Crank Handle, 11/32"

Hello - This single arm operator had the worm gear push out. I cannot find a similar single arm operator anywhere. DO YOU HAVE THE EXACT REPLACEMENT PART OR ONLY SOMETHING CLOSE? It looks exactly like the image posted back in august 12, 2014 in which Tom from SWISCO responded: "August 12, 2014 I ... (cont.)

The rotating window crank gears are stripped. The hinges work fine after I added grease. Can I replace the crank or do I need the whole assembly? Can you identify the make/model?Here are the dimensions of the base of the crank in front of the window frame:- width (horizontal) is 5.5"- two screws (no ... (cont.)

The big arm says "Entry Gard Truth" on it. Small arm has #20810 on it. Measurements appear to match. I'm thinking this will work with Swisco Product code 39-032. Is that correct?

Need help locating new hardware for bedroom windows, attached are the cranks. I will need (2) left hand and (2) right hands.

I'm looking for a Semco crank. The one I need says TRUTH and has the numbers 45240 15. Please let me know what I need to order as a replacement. Thanks!

I have a window in need of a new crank, about 25 yr. Old house. Number on the back of the arm is 40530 and number on the plate is 45047. Pivot point to middle of roller 9 3/8, plate is 4 3/4 by 1 1/4.Can you help me find this? Please and thank you.Njal

I need all 3 parts.

Hello, my window crank part # 0P05-1509 broke leaving the bottom piece lodged in the casement. In addition to the window crank arm I believe I need a #0P051505 casement assembly that has a #0P052020 arm . Can you help me select the proper replacement? Thank You, Sean B.

Trying to find replacement cranks for my older crestline casement windows . Windows to good to replace and have 3 of these crank assemblies (truth) that are worn out, can not find replacements. Any help pointing me in the right direction would be appreciated. Anything that would work even if I had t ... (cont.)

window casement, to open and close windows

I would like to know if you carry this part?

I'm restoring a house from 1957. It has about 25 windows like this, very few of them still operate, Can they be replaced or restored?

Looking for a window crank assembly. U.S. patent number 4,241,541 It reads "Truth" as the brand. This one the short arm reads #30842R and after the joint, there is a second arm attached with # 20810 stamped in it. The larger arm is 9" from the gear to the center of the roller.The base has 7 holes an ... (cont.)

Original part is Truth EntryGuard 31538 (U.S. PAT 4,241,541), 90 degree opening. As photos shown. I also need a folding handle with cover to match the operator. If the folding handle can use as right and left hand opening, then I will need to 2 of them. Please let me know if you carry the same par ... (cont.)

The handle has SEMCO 0n it. It measures about 3" and to the best of my ability it looks like the hole by the set screw is 11/32 nds. Handle is made of cast/iron. Wondering the best place to get them, I need 17.

Malta window. Need crank and lock

Hello, I have attached photos with measurements on some parts that broke on my window. Please let me know if this is adequate information to see what the new part is. I am sorry that I did not send pictures of it installed, I found this option after I already removed it. I also found what I believe ... (cont.)

Hi. I need a replacement crank for a Crestline Window. Numbers on stamped on the inside are "15" and then "45054" Can you help me? Thank you!

Hello ? ? Could you inform me what I need to order from your company to replace this Craftline window operator, and its accompanying handle? The window that it operates is 45" x 28". My husband & I are putting our house up for sale very soon, and have discovered that we need to have these replac ... (cont.)

Looking for one of these. It says Wright 2 on the back