Viewing all customer Discussions for:

39-114L Crank Handle, 11/32"

Trying to figure out whether this website has white foldable replacement handle, cover and lock for the Caradco handle and lock with the following numbers. I don't know if these numbers mean anything or not but they are imprinted on the parts. I've attached photos of the brown handle, cover and loc ... (cont.)

I ordered the crank handle 39-114L to go with an angle drive that we bought a few weeks ago from Swisco. But the crank handle has no set screw, so I have no idea how it is supposed to stay on? This is for a skylight in the ceiling, so it falls off w/out a screw. Thanks.

This is the crank for a casement window tht cranks up from the bottom the internal casting threads stripped out and it connects to the window with two slots and a cam lock retainer

These are the only parts I have the window is 28 inches wide. It is an Andersen window I guess I would need all parts to operate window maybe we can retrofit

Hi, I'm looking for this casement operator. Can you help me cross reference it? I know it's made by Truth but it seems obsolete. I'm hoping I can find about 20 right and 20 left. Thanks Jeff H

I have seven broken Atrium window cranks: 4 right handled and 3 left handled. Please see the attached picture "AtriumWindowCrank.jpg". The number on the crank is 40425 and the operating arm is 9.4" long. Also, I have to replace the handle and/or mechanism for another Atrium Window shown in the atta ... (cont.)

I have a canopy window in need of parts. The crank is OPO5-7540-03. Below are the pics of crank. The last photo shows the missing pieces for the ends of the arms and the mount on the underside of window that the arms attach to. Do you carry these parts?

My Weathershield casement window installed in the 90's will no longer close all the way. I need the above parts I believe. Crank should be white. Do you have replacement parts? Crank has the numbers 45199 and operator has the word "TRUTH" and the numbers 31850. See pictures. Thanks for your help! ... (cont.)

This is the part number/name that I could obtain off the window hardware. Do you have these in stock? I need three of them and need to know how long it would take to get them shipped to me in Colorado Springs along with cost estimates. Thanks!

I am told by the manufacturer that i have a Atrium weatherlock 800 series which they no longer manufacturer. I am looking for 4 replacement handles and they suggested i contact you for assistance Thanks in advance Bill B

The window cranks open and close but will not close completely. Like it's off center or the crank does not crank enough to close the window. I'm thinking i need to replace the operator. The window is a Crestline. I have yet to see even the same type of handles as these windows have. Can you tell wha ... (cont.)

The casement window pictured here and used in this house was built in 1957. I am pretty sure that the windows are Biltwell from Dubuque, Iowa. At least the hardware has that as a stamp identifying the hardware as such. The arm is over 14" in length.

Looking for the replacement to the TRUTH hardware and the soft plastic foam filled seal I am holding. These are K/K Windows as seen on the crank cover. 25+ years old. I am reworking the wood but need seals to replace the old seals. HELP!

Hi, I have a window crank that needs to be replaced.could you help id'ing and quoting it if possible. Thank you tyler

Hello, Looking for two replacement window crank handles (only the handles are needed) - they are marked "19 45054" and look to have a brushed nickel finish. The windows that they go with were installed in late 2006 (to give you an idea of how old the parts are). opening is approximately 1/4 inch. ... (cont.)

Pictures are of the crank for Caradco awning windows marked with a part number(?) 45012. They are not the folding type and are held in by a setscrew. Can you suggest a replacement part?

I need a part for a roto roof window. It's the handle to open and close the window. It's truth 45013. Do you have anything that will work to make window functionable? I have a pic to help find this part. I need two of these. Will your part 39-379 work?Please contact me by phone or email with any qu ... (cont.)

We have three windows that are missing the cover and the Cranks the one window we have that has them I have attached a picture and it says enerpro on it. I'm hoping you can help me out and ship overnight Thanks Jackson H.

In need of a handle and arm for a bow window. The arm is 8 3/4" long. Looks like it can be all one piece. Also need the 4 screws and there is inserts that the screws go into. There are no numbers or name of the manufacturer on the window.

I'd like to get two of these operators and the corresponding handles. Thank you.