Viewing all customer Discussions for:

39-505 11-3/8" EntryGard Track, 4 Hole

I need to replace 2 of these assemblies.

I measured, the best I could, the long arm being 8 3/4" the short arm at approximately 4"

I have Bonneville windows likely from 1995 and the first 2 pics I attached ("1c - 20250817_145005.jpg" and "2 - inside crank and Bonneville sticker.jpg") are from my bathroom window where the small hinge's rivet rusted off. The next three pictures ("Angled hinge & hole.jpg", "Bottom hinges & ... (cont.)

I am hoping that you can help me for some replacement parts. As you can see in my first photo, I basically need most of parts replaced especially the bracket in photo #2. In photo #3 the bottom bracket is #51512- 6" long. The curved arm is #31538A. This is part of a 3 window set with the middle w ... (cont.)

Hello I need help to id this model crank so I can order a replacement. Thanks Steve

i have a left hand crank out casement. 22 13/16W x 69 1/2 High. i need the top and bottom hardware kit for the window. the crank out assembly included. Need new channels top and bottom as well. I have the screws to install. Uploaded three pictures of the style. It only says Wright on the extension a ... (cont.)

Entry guard truth left swing

1. Both are left windows, 30842R on arm, 20810 on arm extender, 40372 on base, 30830 on gear holder, 45012 on handle. 2. 2 left windows, 1 right. 30744 on arm bottom, 20544 on arm extender, 30710 on gear holder, handles same as other 45012. Thank you!

Hi. My customer has a quite old bay window in good shape. The casement flanker hardware is tired. The right side does not operate. The left side does, but due to play in the armature, the assembly pops off the sash where the aluminum track has the gap for removal/maintenance. I am looking to r ... (cont.)

Hello, I have multiple original windows from my 2002 home where the crank arms are slipping out of the track and need replaced. The windows vary in size but all of them have similar hardware in the "Truth" brand. Hoping you could help ID a couple options. 1: Does the hardware need to be replaced exa ... (cont.)

Looking to see if you guys have any of these window cranks available. If you do, you can also contact me at 805-332-4477 thank you

Long arm measures 12" and short one is 8". The base on the sill is 4" and the track on the window is 14".It's for the left side.

I have a Marvin casement window w/ 40574 stamped and the arm is approx 8-3/4" long (from center of nylon bushing to center screw hole aligned with the crank). From center of nylon bushing to end of crank is roughly 11-1/2" See photos for more info. Can you pls tell me part # and/or link to Swisco. ... (cont.)

Thank you for your assistance. Is it possible to replace this window hardware and possiblly the window insert? Please let me know if you can help. Thank you very very much!Rod

2 arms, the top one is 12 inches and other is 5 8nches Kind of hard to see but I put tape measure on arms

Looking to replace the crank and window latches. It says "truth hardware." My guess is this is 15 year old window. No other markings. We have Andersen E series windows everywhere else. See if there is any option in more of an antique bronze color.

Need left hand (viewed from outside) sash hinges - pretty sure these are 10" 2-bar but want to verify. they say Truth EntryGard on them. Your P/N 36-048? I want to replace both upper and lower. Please confirm... one source says a lipped casement window requires a 4-bar but doesn't look the same as ... (cont.)

I need to replace CARADCO windows cranks. I see one on your website and wonder if it will fit. Does CARADCO has many sizes? Thanks!

Looking for advice on my casement window. I have several window that open easily but cannot be closed, especially the last inches of two before they close and are latched.

Kolbe pre-2006.