Viewing all customer Discussions for:

58-099 Gray Pile Weatherstrip, 9/32" x 5/16"

Trying to find balancers that work

Hi, I need help finding a suitable replacement for my weatherstripping.

I have a 1962 built home with original sliding aluminum windows. I need to replace the weather stripping as the old weather stripping is shot (I don't think it has been replaced since 1962) and a lot of air seeps in around the window thru the gaps. The weather stripping runs around the frame of the ... (cont.)

Hello, I have about 8 32x54 double hung windows I purchased from Home Depot, under the name American craftsman, back in 2002-2003. I am looking to replace the weather seal where both the upper and lower sashes meet and lock. The attached pictures showing the white seal is on the lower sash. I believ ... (cont.)

I'm having problems finding the adjusting screws on my plate glass (1967) slider. There are no visable adjusting screws or plugs. All other windows are Wayfair aluminum frames, the slider is unmarked. The door operates with ease, (a rail cap has been installed) but does not line up with the jamb. I ... (cont.)

Base is 9/32 long and brush 5/16 tall Has a thin piece of plastic running through it

I have a few feet of the original (unused) weatherstripping. It has a 0.250" tall pile and base. The well used stuff in the windows is 0.225" tall, but it's spread out from use. The attached image IMG_0614 is of the virgin stripping. The other two are of the well used stripping. The width of th ... (cont.)

Trying to get what you believe are the correct measurements so that I can place an order. Thank you kindly for you help.

The weather stripping slides into the slot on plastic piece. Picture shows side with weather stripping top of door is with out.cant find right size. Plastic piece of weather stripping that slides into holderis either 9/32 or 5/16 I think. Fuzzy part is like 2 pieces with plastic in between. Are the ... (cont.)

Hello, Looking for replacement pile weather stripping for some old aluminum sliding glass doors. I haven't been able to figure out who made these doors and finding parts has been tricky. It looks like the weatherstripping is 1/4inch by 1/4inch. Thanks for any tips.

I'm looking for fin seal strips for a Cardinal (I think) sliding patio door. Bottom fin strip is 1/4" or 7mm wide, and the vertical fin is 1/4" tall. Door height is approximately 76-1/2" tall. I also would like to replace the top & bottom rubber seals on the stationary door (where the 2 doors meet ... (cont.)

Hello, I've messaged you before regarding some of these parts, but I'm still looking and have some more info. The first pictures are a channel piece we had trouble identifying. I recently noticed that they have the number 0132 moulded inside. I found a local supplier but he was charging more than ... (cont.)

Hello, I'm looking to replace my weather seals. They look like they measure at 1/4 inch wide across the base. I was thinking 3/16 would work.

This is the weather stripping I need, what I ordered was wrong.. I need enough for two doors Thank you

I'm having a hard time finding a match for two rollers: Roller stamped A-S NYC 7867 3 5/8" long 1 3/8" tall 3/4" wide The roller is stuck inside, but the OD is appears to be 1 1/4" The brass roller has no stamps 2 1/2" long 1 1/4" tall A little over 5/8" wide OD wheel 1 1/4" Additionally, I canno ... (cont.)

I want to replace some weatherstripping on the sliding doors, do these pictures help you determine what I need? Thanks.

I have three very normal sized vinyl windows that I need replace the weatherstripping due to dry rotting. Please help me with the best replacement part and could you also please recommend a good spline tool to assist with installation. Thanks, Rich

I have four pairs of Alcan sliding glass doors that need the white weatherstrip that seals the edge of the door on the outside and inside when closed. Attached is a cross section photo. The width of the "T" is approx 5/16 inch wide and the bulb itself is about 5/16 in diameter. You can see in the ph ... (cont.)

Need help with (bubble seal) I order the pile weather stripping 58-099 which is 9/32x5/16 that fit in the Channel because it is 9/16.but the bubble seal I order was 3/16x5/16 that doesn't fit in the channel it is to small can you help me with the Right bubble seal the will fit only one I see that ... (cont.)

Hello there, I got this piece off of my sliding closet door but seems to fit the sliding glass patio door as well. These are town homes so it seems like everything is standard all windows, closet doors etc seem to be the same size. I'm not sure what the minimum footage to order is but I'm thinking t ... (cont.)