Viewing all customer Discussions for:

75-005 Spiral Balance Charging Tool for Non-tilt Windows

We removed spiral balance (23 inch red tip) and could only find remnants of the shoes. We've purchased the balances from swisco with 15-012 shoes. Then we looked harder at the window frame and found what I think is part of a shoe attached to it. The photos are of the jam remnants and the window fram ... (cont.)

Our window is 30" in height and 33" in width. They are difficult to open, it sounds like a spring inside is having a difficult time releasing tension. Do you have a replacement tension rod? Thank you

Please advise and provide links to replacement parts for my non-tilt windows. There are no markings on my existing parts.The tube diameter is 3/8". It appears to me that I would need the following types:1) Spiral Balances, 3/8", 29" length, Non-tilt2) 1) Spiral Balances, 3/8", 31" length, Non-tiltAd ... (cont.)

It's a premier window brand. It is a tilt window with the foot and shoe similar to the Marvin.

Hi, I am trying to replace my old spiral tube window balances. This house was built in the 50s and it seems like these are still the original windows. Surprisingly enough the windows are in good shape just need some updating. There are no markings on the units. They are 23"long, 3/8 wide. The sa ... (cont.)

Body is 12 in Long 3/8 in tubular and screws in at the top. I cannot seem to find the bottom connector that locks it to the window. Please help me if you can thank you Bill

Window is a non tilt that measures 22 3/8" high x 41 7/8" wide and weighs approx 12lbs. The spiral tube measures at 21" and is 9/16"(5/8). Has a foot bracket like your #32. Would this require the red or the blue spiral balance for proper lift!Thank you Dan

I have four identical windows and one smaller one that need to have their spiral tube balances replaced. All of them have broken plastic tubes that seem to be about .50" in diameter. The four identical windows have a 33 " tube, and weigh just over 12 lbs. The smaller window has a 28" tube, and proba ... (cont.)

I am trying to find these old "spiral" style balances for 1950's wood windows. They do not function like a spiral balance though. The square end push's in about ½" and you can wind it up and it will unwind. It does not pull out. Can you please let me know if you have ever seen something li ... (cont.)

I have a few windows that are having trouble opening and staying open. I assume it's the balancer. The spiral has fallen down on a few of the windows. Will I need to replace the whole balancers or can I re-tension the current balances and re latch it. It's the H-R40-48x72 series 300. If I need to r ... (cont.)

The spiral tube is 30" and 31" to the tip of the spiral. The tip looks like it may be red, the windows were installed on 2004. They are single pane non tilt and the mfg. code is GA-1. I can't tell how the spiral attaches to the bottom of the window. The one photo try's to show the one bottom corner ... (cont.)

They are 25inches and 5/8" but there isn't a colored tip and the piece that screwed under window frame is attached unlike the ones I see on the website

The tube is 28 7/8" long. The windows are aluminum, original to house, built in the 70's we believe. One of the pictures show a number "2" on the end piece. Am not presently at house, but can get picture for you of window and inside edge where part fits. Believe I am needing for more than one wi ... (cont.)

i just ordered 816 of the s 200 spiral balances 8 at 27 and 8 at 29 i need the hardware to attached it to the window i didn't know it didn't come with it.I think I ordered the wrong balances I need them to attach to bottom of window can you help me get the Wright ones doing a restoration on a house ... (cont.)

I'm attaching some photos of my spiral balances from 1961 aluminum windows. Can you tell me what the best replacement is for the balance itself as well as for the shoes? Note the clip on plastic that keeps the window in the channel. Thanks!

I have single-hung/? Side mounted sash brackets that screw in from the side inwards. It seems I'd need to take the sash out of the frame to replace it. How should I do that?

I need tool to wind spring and tool to keep clip from coming out from the bottom of the window frame.Also,I need plastic incerts at the top of each side of the window to keep balance tube in place.Please examine photos.Thanks!

Hello, I've sent several pictures in order to see if you might know what brand of Windows I have and to identify the two forked brackets that are screwed into the window frame on each side of the sash. What are they called, and what do they do? I really appreciate any information you can give me. I ... (cont.)

Looking for a 36C product code S770-36. The one I'm replacing attaches at the top with a little bar, the one in your catalog uses a screw. Would I just remove the hanger now in place and use a screw for this one? Thanks for your help.

can you help me identify these parts