Viewing all customer Discussions for:

80-102 6' Sliding Door Track Cover, Small

I replaced rollers hut track is worn so bad does not help much I was looking at your 80-102 track cover as an option to fix problem. As near as I can tell track is 1/2 inches tall and width of track is 1/8 inches. Is the 80-102 the correct part?

need track covers for a 3 panel12ft sliding door. Each panel is 8ft high x 4ft wide.Also I need all the weather seals replaced. What do you recommend I buy

Hello SWISCO, Im looking for the plastic track liner for my KK sliding door. You can see in the photos that mine is broken and missing, except for the short piece still attached. Can you help? If not, can you assist me with finding the company; "KK" or advise anything about it? I haven't been ab ... (cont.)

Two new rollers New weather strip the channel measures 3/8 inch Outside measurements Track cover 6 foot

I can't get my 80-102 track cover to stay on its track. The top track is one I have been trying to install on it was sanded smooth but cannot get them to get going without bending up as I go. Tried a small block, hammer direct and a longer block same issue: wants to keep bending up as I go and will ... (cont.)

I need Two rollers and the replacement track for my back sliding door. Had no part number on them

Need two plus 80-102 & 75-077

I was wanting to get a track cover for an Andersen patio door. Will you`re overlay fit? Was also wanting one for the screen. Door was made in 1982 and the 6' should be long enough.

My house was built in 1998, and I have a patio Oak sliding door with "Gaurdian" glass. I think the door is a "Vetter" since the windows are all same. The 2nd photo is from outside and 1st from inside. They both show the deteriorating rubbery track weather shield that happened as the Nylon rollers go ... (cont.)

Hi,From what I can read printed on our door (there is printing on both sides causing blurring):Guardian Corsicana TxBS 6206-198116CFR 1201 II16NSFR 9201-1984SGCC 1245S 1/SU 3MMCAN 2-12J-M79Would a track cover work? Or would we need to replace the whole track piece? Which one should we purchase? Also ... (cont.)

I live in a home build in 1960 with Arcadia aluminum sliding glass doors. I need two new rollers and a track cover. Can you advise me on replacement parts?

One photo shows the track the door runs on. There had been some kind of plastic or silicone covering on it that cracked and broke away some time back. It was damaged beyond repair so I threw it away. Now by pushing the door open and closed without that covering, I've damaged the door handle/locking ... (cont.)

If the track is a little bent do they make apart that would go over the trackSo the screen will move smoothly Thanks

I have a 3 panel sliding glass door.The track for the first door has developed some depressions on the raised track guide and makes the door drag the track. I have adjusted but that makes it rubs against the top track.I need to find a solution.Can you identify a contractor who can make the repairs?i ... (cont.)

Hi I'm having problems locating these rollers. The wheels are 1- 5/8. I hope y the pictures you can help me. It does have the little u shape end that slides up around the top screw to hold it in place. Thank you

Have a bit of dents in about 4 feet of track

Hello,I have a townhouse in Florida with several aluminum sliding doors that need an overhaul. I would like some help identifying the hardware I need to replace which include; Track or track cover, roller assembly, top plastic guides, weather seals.Attached are some pictures with a measuring tape.Th ... (cont.)

Hi, We are having trouble replacing the taped grey plastic strip. It was bent and flipped up and is now being held down by duct tape. People keep tripping over it. It slides under the stationary door as well. Thanks for the help! Jim

I need 4 Track inserts Item 5 on the parts list for PGT SGD 5470/5570. Our doors were installed without this after hurricane Irma. Parts list says it is an aluminum extrusion that is installed into the sill for panels to ride on and ours is missing so plastic is wearing. it's a 6 foot doorI have ... (cont.)

Question is - I have a 6 foot sliding glass door with a damaged track. I have thoroughly cleaned it and prepared it for installing the replacement 6 foot metal track cover. I am wondering if I can cut the cover into 2 pieces and join them at the cut ends in the middle of the track making sure there ... (cont.)