Viewing all customer Discussions for:

81-223 1-1/8"dia Replacement Steel Concave BB Wheel

Hi folks, I've purchased from you in the past and now I'm looking for Stainless Steel Rollers for my sliding glass door. Can you help? I've included pictures. Thank you, Bret

Might be a 40 year old door

I have two doors each with two rollers marked "Del Mar Eng 448-2."Each roller is comprised of a single steel wheel 1 1/8" diameter. The maximum thickness of the assembly is 11/16". Flange width is 3/4".I am familiar with your 23-043, but would prefer a 1 1/8" wheel, made of steel. Do you have such?T ... (cont.)

Hi- I have a fairly old door which contains a roller which is very similar to Product Code: 81-093, however, the dimple width of yours is too wide to fit. Mine pretty much snaps into place so going that large will not fit. Do you have anything that could work? As a backup option -- could I just ... (cont.)

This is from an aluminum door that came with our house, built in 2007. The only marking is on the case, it just says "Ultra." Case is 2 3/8" long, 1 3/16" tall, 11/16" thick. Wheel is metal, 1" diameter.

Can't find any numbers on door or rollers need new rollers or parts to rebuild and track insert for replacement rollers

What roller do I need?? Can't find right part. Thank you!

The bearings on my less than 2 year old door have died. I am attaching pictures of all the info I have and need to order new rollers. Please help with identifying the correct rollers. The purchase order numbers and warranty numbers are attached.

Length 3 1/8" Width 11/16" Height 1 1/8" Wheels 1 1/8" Wheels are metal w/ball bearings Thanks Darren

I need to get a replacement for the rollers for my sliding glass door. The plastic wheel does not hold up to the weight of the door.

I cannot seem to find rollers that match my current rollers exactly. The measurements of my current rollers are identical to the 81-030 rollover on your site, except the wheel diameter is 1 1/8 inch as opposed to 1 1/4 inch. I am not sure if the roller will work for that reason. My rollers have a ... (cont.)

Dimensions: 3/4(w)x1"1/8(h)x1"1/8(d) Wheel: Metal(2 wheels) Letter "V" marking on the side

Good morning - a contractor told me I was going to need your part numbered 81-156SS to replace on my sliding glass door, as they could not get the door adjusting mechanism to work. Of course I did not take the door out to double check - but when I went to replace it... pictured you can see the part ... (cont.)

Do you have anything similar to your 81-228 with a nylon roller with a stainless steel ball bearing? (Ideally with a 1/4" Shaft)

Please note the angle of the mounting screw, indicated by arrow in ..389 of the pix. This seems critical and has proven hard to find.

Looking for 2 replacement rollers. Width 5/8, wheel diameter approx 1-1/16. Overall length 4-5/8. Thanks.

comes from an IGA sliding patio door

I need to replace this double roller assembly on my sliding glass door Length: 3-1/8 Height: 1-1/8 Width: 3/4 Wheel Diameter: 1-1/8 Anchor screw is above the leveling screw. Both on the end. 2 metal wheels ** DOES THIS COME IN STAINLESS STEEL??

Miles image0.jpegimage3.jpegRoller= 1"image4.jpegWidth at flair = 1/2"image1.jpegTotal height = 1"image2.jpegTotal length= 2 1/8"If at all possible, I'd like the lower track as well.It is 56 1/2" x 1 7/8 as shown below.image5.jpegThanks

My name is Michael, want to know if the part is available. If not, can I just replace the wheels? If so, is there wheel parts and tool to take the wheels off? Thank you so much for you soonest advise on what options are there for me.