Viewing all customer Discussions for:

82-226 Mortise Lock, 4-5/8"

The lockset screw is broken. I'd like to purchase a replacement mechanism. Lockset is 1 1/8" deep. Screw holes are 4 11/16" apart. Inside it says it is a 2260. Us Patent 51257030340398

Hello,I need to replace the internal lock of my sliding patio glass door. After contacting the manufacturer 'Harvey', they referred me to you, as the door was manufactured about 20 years ago. The issue is that the internal lock does not lock anymore. The "hook" does not come out by itself. Pleas ... (cont.)

Hi I need help in replacing this handle please the doors got to be like 20 years old

can you please tell me the part number I need to order a door handle with lock for my Simonton 6068 patio door?

Older model sliding patio door. Latch evidently worn out and will not operate as usual. There are no names evident, but there is a symbol that looks like an abstract Sc on the side of the lock mechanism. (See picture). I tried to use a ruler for help in your identification.

Looking to replace both main door and screen door latchesThank youJim

If you cannot read the number code in photo "Door lock 2", it says 2300-1061-2. The lock is broken and we're trying to find a complete replacement for the lock most importantly but also the handles. No other markings, names or numbers to be found anywhere on the door.

I am looking for a door handle with key for patriot vinyl sliding glass door. White.

Hi, I am looking for replacement parts for my exterior sliding glass door. The sliding door is vinyl and is 93 1/8" high, 36 3/4" wide. I need a set of rollers for the bottom left and right sides of the door as seen in the attached 3 photos. I also need a new door handle inside, outside, and the loc ... (cont.)

The door handle was gone. It didn't have a lock and key. It's a patio deck door that's up 2 stories with no stairs to it. We remember it only had a lever on the door handle to latch and lock it. We found a picture of what it looked like before and we think there dog destroyed it. This was during a ... (cont.)

Hi Swisco, I found your patio lock 82-089 to be very similar to this one below, however the screw pattern on the one below has the screws go through the handle whereas the one you list has the screws go below the handle. Could you confirm if your part 82-089 could retrofit here or if not identify t ... (cont.)

No markings. Overall length 6". insert is 3"X1/2"

Hello i am looking for the part of which i think is called the striker for a single hook mortise lock. Forgive me if I don't have the terminology correct. I will attach pictures which i hope will help. I don't know the brand of the actual door because i cant find anything stamped or tagged anywhere ... (cont.)

Need to replace everything shown above. The measurements of 82-226 seem to match our measurements except for the center to center for the screw holes. Ours is 4-3/4" - everything else is the same. Also need to know which handle set and/or key plug we would need. The photos show the original parts fr ... (cont.)

Looking for a replacement door handle and lock for my sliding glass door. SGD-R30-144x82 SGD_R35-96x82

Please see the attached photos my slider door was installed with no handle. I need a white handle that will match this hole configuration and mortise

I have a 4-panel glass door. The windows are double pane, and the panels are very heavy. The 2 inside panels slide open. I have two problems with the panels that slide open: 1. The latch on the door has broken off (IMG 3121). 2. The seal on the sides of the doors do not fit snugly against the ... (cont.)

We think the middle hardware piece needs to be replaced. SH-72-1 SH-72-2

Need a complete lock handle and keeper

I looking to replace two of these, since I'm changing them I would like Key entry. PPG Herculite slider doors See images and I'm hoping you can help. Michael