Viewing all customer Discussions for:

82-306 Keyed Exterior Sliding Door Pull

Do you carry a replacement for this handle?

Hi! I have two Weathersure sliding doors in my house built 1986. Need replacement window locks and handles with all the mechanisms. The exact door model number reads WS IGCC (r) 408 OMHO 7567. The distance between the handle holes is 3 and 31/32. Can you help me with new parts or something ... (cont.)

I need a door handle with lock to fit the pictures below. I don't have the original. What measurments do I need?

Hi, I have two sets of sliding doors and I am sending you a picture of the part that I need. This part is what is on the outside of the door, and I don't know if I can purchase just this part or if I need to buy the entire handle/locking mechanism. The screws are exactly 4 inches apart. Please let m ... (cont.)

It is marked Canadian Patent No. 919213 Patented 1973 and Pat. No 3.596.954 it is 7 1/4" long and between the screw holes is 5" and there is the lock apparatus comes out of a 1 inch square.

The pictures of the door should be attached to this email for you to forward. Travis

The double roller has a part number stamped on the inside. I can't read all of it. It ends with 116K-5. I need all sorts of parts for these doors, as I have 5 installed in my house. I cannot find a manufacturer's label anywhere. Your help is appreciated.

I am desperately seeking a replacement handle. It has a mortise lock stamped with 2300-1061-H on the side. The keeper is fine. I cannot find any manufacturer names anywhere on door. The door is 1 inch thick. I need a new mortise lock and handle set with keyed exterior lock as we do not have a key. I ... (cont.)

Hello, I bought a 82-003 handle/latch. It fits great and everything works fine. However I would like a key type lock instead will this work 82-261 ? my door is 1 inch thick. does it come in any other color, would prefer darker color to match door. Thank you, Jim

I live down in North Wildwood New Jersey and I'm restoring a 1969 Nautaline Houseboat. I'm trying to find a keyed locking door handle for the rear sliding window/door. The original handle is missing. The door is just shy of an inch thick. Approximately 15/16 of an inch. The holes are 5 1/2 in ... (cont.)

I have a sliding glass door with a handle that appears to be your 82-005 with a 4 15/16 screw spread, installed new when my house was built in 2000. I want to add a keyed lock on the outside. The 8 1/4 inch long plastic pull on the outside is fully recessed into a 7 7/8 x 13/16 inch cutout on the o ... (cont.)

I have a sliding patio door about 30 yrs old. Missing out side door handle. Purchased this condo with missing handle. Up loaded 3 pictures. Picture #2 is the outside for missing door handle. It looks like the handle slides down on the outside bracket. The inside item listed below matches the inside ... (cont.)

This door is a main entry point and lately when locking the door outside by key or inside by latch it does not lock and requires 2-3 attempts to succesfully lock. The latch is loose meaning the small stick which goes up to lock or down to unlock is extremly wobbly and can be pushed more ways than j ... (cont.)

Hi Swisco, I'm looking to retro-fit my sliding glass door with an exterior key. I'm looking to buy just the exterior handle and key hardware. The interior handle is in good condition. Thanks! -Chris

The pull to the locking handle of my sliding glass door broke. It is the outdoor-facing plastic pull that attaches on the left side of the door from the outside (locks from the inside). There are (2) 3 inch screws that are also damaged. The only markings I could find are on the inside the locking ha ... (cont.)

Hello - Sending three photos of part required for sliding glass door. The length of the wooden handle is 11". The holes that affix the wooden handle to the metal bracket are 6" from center. The holes that affix the handle to the holes in the door are 5" apart. Markings on the locking mec ... (cont.)

I have a sliding glass door repair business and have a large demand for a much superior lock than what most sliding doors come equipped with. I would like to find a lock assembly that will install and utilize the existing hole that is already there. Original lock assemblies mounting screws measuring ... (cont.)

Canadian PN 919213. Dimensions

Hello, My mother had this door installed a few months ago and soon realized there is no keyed lock with it. Can you determine what lock assembly is needed from the attached photos? It appears to have a punch-out to install a mortise lock but, without having that tumbler I do not want to attack th ... (cont.)

Hi there, Would it be possible to install a lock cylinder for exterior access through the patio sliding door. Perhaps drilling out the exterior cover and installing this: Sliding-Door-Lock/pd/Patio-Glass-Door-Replacement-Key-Cylinders/82-303 Please see the attached pictures.