Viewing all customer Discussions for:

19-029 Short S-Clip

Hi, We have a window (manufacturer unknown). The only thing visible is that it says 18HD on the balances. I need replacement balances because the window will not stay open unless it is propped up by something. Would like to replace jamb liners too. There are no identifying marks anywhere on this ... (cont.)

looking for replacement balance. Windows at approx 36 years-vinyl jamb liner

Attached picture is for a Marvin #232023 window 23X26 size. I have one replacement part with a 22H on it. It measures 23" end to end just the metal part. I need three more units with the clips for the top and the black piece that runs inside the channel connected to the rope that window clip fits ... (cont.)

Is the top clip included with this balance? If not, which clip do I need for the inner window? I plan to install this balance on a Marvin window circa 1978. Measurements and photos seem to indicate this is the correct balance. What are your thoughts?

I believe i need to order a new series 745 channel balance however the size i need is not listed on your site. I have a measurement from the top to bottom of the metal channel at e6 1/2

I need to replace a balance for a tilt-out window. I've looked hard for identifiers that indicate the manufacturer, but I've found none. The window was installed when the house was built in 2008. The window is a double hung tilt-out, roughly 35" by 77". I'm sending a picture of the balance, wh ... (cont.)

Wondering if I can get hooks only. Thanks

I have the same malta windows in my house as I post D51793 that need to be fixed.I have a couple of questions. I have half of the windows that have the glass dimension of 31" wide and 23 1/2" high and half 31" wide by 36 " high. Which balance would I use for the larger windows. Also I dont want to u ... (cont.)

Length is 31". My bathroom scale measures @ 20# but could be off. Balance is 1/2"+ with ribbed profile. Spacer at top is about 1 1/2" long.

Hello,I have several windows that won't stay where I open them to. They can free fall. They are approximately 20 years old and have a blue plastic part (I think it is the clutch???) that is broken or the string going to them has broken. I see that marvin uses a new system. Is it possible to upgrade? ... (cont.)

I have Rivco tilt windows from the late 70s. I need to replace something that looks like a 24

Here are the pics. Please identify and let me know. Thanks Bala

Hello, the stamp on my balance reads: 12KL B.S.I. pj The balance seems to measure 9/16" wide and 1/2" deep. I tried to replace it with a 12B JE. But the replacement is attaches differently and interferes with the operation of the window. AND, it doesn't hold the window up. I've been to a lot of ... (cont.)

The pulley on a window balance broke (see photos). The balance is 17 inches long and most closely matches the S770-17 part. Is there a better matching replacement part? Looking at the photo, it looks like I'd need to drill out the rivet at the top end and move the hook from the broken unit over. ... (cont.)

The length is 25 inches. Can you tell me which part to order? Thanks.

Is it possible to "flex" guide open to remove and replace a 751 series channel balance? If so, I would rather not remove and replace wooden trim and not risk damaging it (I have 5 windows to fix). Thanks, Steve

Trying to find a replacement. Window is approximately 8 years old. Unknown window manufacture. Looked every where on the window, unable to locate? Tilt window. If I did the measurements correctly. 36" long, 1/2 wide and 1/2 deep.

Hi, I have WS block and tackle balance with knife shoe. The Sash say 30HD 102 DB I found the following model on your website but the picture doesn't show me what kind of shoe would work with this. It has a the screw on the top and a S pin Would this replacement part work ? 34" Series 751 Ch ... (cont.)

Can I replace the Channel Balance without removing the jam? The jam removal would require removal of very nice trim that I may damage. Preference is to do it in place. Spring broke on both sides. I got the old ones out, but not sure I can hook the top. Could I use the old hook?

Hi, Didn't see anywhere where the 751 ribbed channel balances come with the clips for hooking onto the jamb liners? Do they or do I have to order separate? Thanks, Pat