Viewing all customer Discussions for:

19-029 Short S-Clip

Only identifiers 20D sideways IS,then RB. Looks like it attaches to a pivot lock shoe similar to 15-178

The window mfg was/is WeatherShield double hung windows the length of the insert is 34" x 5/8" channel width is 11/16". I also attached the stamped "code" that was on the part. The part failed with the breakage (3 pcs) of the spring support part (pic attached as well).

Balance has marking unique balance 33b,do not need pivot show as shown

I have a house full of Ellison Windows that are 20 years old. I'm getting numerous glass sash glass replaced and 2 of them have shot balance mechanisms. Attached are some pics. One is a set of 36" and the other is 30"; pics attached. There are no markings on the parts.

I need replacement pivot shoes for a Coil balance system, Lincoln window? Thanks much, Jack

Looking for pella replacement block and tackle with locking shoe. Architect series, Double hung, tilt wooden window. 28c is stamped on it. S-clip at the top that hooks onto the top of the jamb liner

My part looks most similar to the 795 however the receiver at the bottom of the channel that holds the window pin does not come out. Please advise.

HelloI would like to order two window balancers S770-28B. However, the one in the photo has a bushing the top for a screw mount and the ones i am replacing have two rivots near the top for mounting. Is there a price differance? And how do i indicate that on the order? I also need four pivot shoes. T ... (cont.)

Which window balance best fits these pictures. Note that it is stamped 27D.

I am not sure of the window manufacturer. It would have been assembled sometime around 1999 as that is the time my house was built. I have several windows that need the balances replaced but I am going to start with one of the smaller windows to make sure I can do it. I am not certain how to remove ... (cont.)

Hope you are well. I have a double hung vinyl window in need of upkeep. I removed the sashes and they each weigh 12.6lbs. I removed the balance and it is one piece of vinyl with an aluminum balance inside. The balance channel measures 33" (h) and 1" (w). This is after I removed the vinyl insert that ... (cont.)

The balance in my existing windows do not resemble anything on your website. It appears to consist of a spring that is attached to a clip that is directly embedded into the window jam and a plastic shoe at the other end of the spring. On most of the windows the spring has either detached from the ... (cont.)

I would like to buy balances for my Loewen single-hung tilt windows.I think I need to special order because they are nearly thesame as the S751-37 (36TG), but mine have smooth (non-ribbed) channels.Here are the details:Type: Loewen single-hung tilt windowOverall window: 39"w x 67"hSash: 39"w x 40"hS ... (cont.)

Hello, I have these window channels and I can find any info on them online. The only markings on these are on the balancers that are marked 24HD BSI.

Please help me identify this balance. I have several windows broken which I'd love to order parts asap. Let me know what additional pics I can send. Thank you!Bill

Window balances are non-ribbed u-channel 36 inches long with the number 35e stamped in them. I need to remove the entire side plastic insert after removing both windows to install or remove balances.

The metal channel is 28 in. long, 1/2 in by 1/2 in. The spring is 13 3/4 in long.

Will need a few of these for damaged hardware. thank you

Hi. I need the parts in the pictures. Balancer and pins for 5 windows. Also a lesson on how to install them! :)thank you!Scott

I have a broken sping balance for a large double hung window. Brand of window is EcoVue. It is a vinyl replacement window installed in 2009. The spring valance is 24" long, 5/8 "wide & 5/8 "deep.