Viewing all customer Discussions for:

S380-30 30" Series 380 Channel Balance

Looking to purchase a couple of these30"

Hi, I'm looking to buy some replacement channel balances I uploaded some pics. The model number is 2920C Bsi. It is 30" long

Looking for a Swisco balancer to replace the one in picture attached. Also need top sash part also shown in the picture. 1 balancer has part #2930, shown in picture. A second balancer has a part number if #3620 which is a different sized Alcan window. Please advise if more information is needed. ... (cont.)

Regarding Oder #1152143, I ordered (8) of the wrong S380 series 30 inch channel balances. As you can see from the picture, the channel balance on the top are the ones I ordered (spring is 19 inches long). The channel balance on bottom is the one I need (that spring is 15 inches long). Can you ple ... (cont.)

The balance looks like series 380. 2940We measured 30 inches long, half inch wide.Other numbers on balance are 24. 4 BS1 TE.What do you experts think?Thanks, Kirk

1-marked 2940 bsi vk measures 1/2"wide 31"long and a 1" base plate 1-marked 2840 bsi ax measures 1/2"wide 30" long and a 1" base plate I believe someone replaced the balance with the wrong size (2840) The window measures 51" x 61" inside the house

All the windows in my house are broken and do not stay up. The window sash rods appear to be intact. But it looks like these plastic clips that screw on to the windows are broken on both sides. I need help identifying the top sash guide. Also do you know if the bottom of the window need sash guid ... (cont.)

Hello, I have a window balance which is stamped 29-9, but your selections don't appear to go that high for the size balance/shoes. Is the only way to properly identify the correct strength rod to weigh the window?

I need help identifying the Series for my 2930 Channel Balance for a Non-Tilt Lawson Window. Photos attached. Thanks

I'm looking for 4 of these replacement parts but I'm unsure of the correct part# to order. Channel is 30" long. Would like it complete with new plastic parts/shoes. Can you tell me what to order?

Hi, I need 2 brand new side window balance's for my 15 year old Simonton windows. I have included the window manufacture sticker that is on the upper right hand side of the window. I can not find any markings on my existing balance. I believe with the sticker you should be able to see or have what I ... (cont.)

My windows are very hard to open. I managed to get the window out. I would like to know if you have an assembled channel balance's for replacement. These are side by side windows so I require (4).Thank YouJohn

Hi,need 8 channel balances for harcar non tilting windows. house was built 1989 only numbers on balances are 29B Q. 30 inch long without end pieces. 9/16 widethank you,james

Channel balance for Lawson metal windows.

The 30 in metal bracket has a stamp on the back " 29 9 CX CMC 7"

Balance Length: 30 inches-Markings on Balance: 29 5 FV CMC 2-Weight of sash: 29 LBS.width: 1/2"What do you recommend? Thanks, Bob

Stamped....29 2 GU. CMC. 2 Size....1/2 x 30

I need to replace a balancer for a Milgard window (Installed in 2002). The part is marked 29 4 DV CMC 7 (see attached photo). I have also attached pictures of the two ends of the balancer and the length of it. The metal groove is 0.5 in and the length of the metal part is almost 30 inches. Not su ... (cont.)

Hello, I am looking to order two channel balance parts for a non-tilt window that is approximately 30+ years old. I have uploaded three different picture views of the same type of channel balance, and a screenshot of the inside of the window frame. The length of the channel balance is 30 inches long ... (cont.)

Hi!I have about 6 or 7, maybe more (need to check them), Lawson windows (non-tilt) that need new channel balances. The windows are about 11 years old. The plastic parts are breaking, or the string or some have the small metal pulleys cracking and breaking. Should go for replacing the entire assembly ... (cont.)