Viewing all customer Discussions for:

S380-32 32" Series 380 Channel Balance

The pics have the numbers 1st 25 2 need 4 sets for a total of 8 channel balancers 2nd 25 5 IL caldwell 2 sets for total of 4 balancers 3rd 25 4 cadwell JL 2 sets for a total of 4 balancers 4th 31 3 GL cadwell 2 sets for a total of 4 balancers

I need two of the channel guides as shown in the attached pictures. The length of the metal section is 32".Thanks,Brian

There are no markings. I have two different sizes both with 1/2" channels. One is 32" and the other is 26"

Window balance. Do you have these in stock? 31 5 KC CMC 2 Thank you!

I need a replacement for a window balance, here are the pictures and the balance size is 32 inches. Please let me know if I need to provide more information. Than you.

Hello,I have channel balances that need to be replaced, but I'm not sure which part to order. Can you tell me what I need? Please see the attached photos for reference.Sincerely,Anthony

Dear officer: I am looking for Unique Balance (09/05) 31-D-40. I noticed that some home owners were also looking for the similar product. https://www.swisco.com/discussions/Unique-Balance-0505-32-D-40_26-D-40-replacements-77-56922 However, my balance is a little bit different. Thus, I am curious ... (cont.)

Old 1994 EPI window. 32" channel 5/8". Got four of these laying around????

What is your matching part number for this item? The channel width measured 0.557" (on the channel metal side) to 0.649" (on the channel open side that which has an stuck out edge).

# on larger window balance is 31 5 JX - CMC 7 # on the smaller window balance is 31 4 PG The top and bottom are the same design in both I need to replace the balances in 2 large AND 2 small windows

I have a non tilt EPI window. I need a spring coil pulley balance. It has 3150 engraved on balance. Casing measures 1/2 inch. Length is 32 in. Not including the plastic ends. Which balance do I order.

Hello, my balance is stamped "31 3 IS CALDWELL". It measures 31" long and width is 1/2" on open side and 5/8" on closed side. Both top and bottom shoes have wings. Thank you.

I have a customer that has a long list of sash balances to replace. Here is her list and a couple pictures 31 5 JV CMC 2 (need 7) 31 3 HV CMC 2 (need 2) 31 5 GV CMC 1 (need 2) 31 3 GV CMC 2 (need 2)

Hi, I'm looking for replacement balances for my philips windows. The existing metal balance is 32 inches.

Hello, The nylon wire has popped in a couple of my balancers, so I would like to replace them; however, I don't know the part number of either the wire (assuming it's field-replaceable) or the whole balancer assembly. I also need the clip in the window channel that can be seen in image 6024 attached ... (cont.)

Looking to replace what we believe may be block & tackle window balances?? Our window (from the mid 1990s) doesn't seem to want to comfortably close all the way and just feels like it's putting unnecessary pressure upwards on the locking mechanism (which seems connected to the base of the upper wind ... (cont.)

The shoe has the number 15P102 in it. The end in picture that starts with 99 should have two wings on it. One broke off. The metal is 32 inches long.

Markings= 31 5 FU CMC 2

Channel length 32" I need help identifying the proper replacement. Let me know if you need better photos or other measurements. Thanks!

Hi there,The stamp is marked 31 inches, but when I measure the metal channel, it is exactly 32 inches. Should I get the 32 inch balance? Also, i have attached the stamp on the balance. Can you decipher this for the weight? Thank you,Louis