Viewing all customer Discussions for:

21-007 Bifold Door Guide Pin

Missing top and bottom hardware for 2x bifold dodoors

I have a metal bi-fold door using guide pin 21-007 on the top and bottom sliding side of the door. When opening or closing the door, the bottom of the door binds on the lower track. I have adjusted the bottom pivot to lift the door as much as possible with out binding on the top track, and adjusted ... (cont.)

Hello, Can you assist me with obtaining door pins and track for these late 60's-70's metal bi-fold doors please? There are two panels. each are appx 24" wide. Each panel will be installed separately for two seperate closets. Attached pictures for your reference. Please advise, need parts yesterda ... (cont.)

Hi! I'm trying to replace the plastic pin caps on my mid 1970s home. The only label found refers to the doors as "model C". I bought Swisco part Bifold Door Pin Cap 21-111, but it seems the pin is a bit wider than the cap and it won't slide in. The new cap's length is fine. What other cap can I use ... (cont.)

Im looking for replacements for these pieles. Thank you.

Hello, can you help me with finding upper and lower tracks,door locators,slides and bump stops? Attached are my steel glass bi-fold doors with door hardware in place. I need 48 inch tracks

I am replacing a wooden bi-fold doors with metal. They are 4-feet in length total with 4 panels. Have tile flooring and wanted to see if I can install this with just the top rail only and get by using a wooden bi-fold door bracket on the bottom. Let me know the part numbers that I need to buy. th ... (cont.)

Hi, i am looking for hardware for Slimfold Closet door. I sent you the pictures of de model of the door, the top pin and bottom pin. The size of the pin is 5/16 in width. The piece I need is the nylon fit on the bottom pin and the top pin. I need 10 top nylon pieces and 10 bottom nylon pieces . Can ... (cont.)

This is at the bottom of the door. It snaps in to metal and rides in door floor mount

I want to fix my slimfold bifold door. I'm not sure which part to order. Would it be possible find a replacement part for a damaged guide on the bottom of the door. Thanks

I am in need of some parts for half of a 1960's era bi-fold metal door. The track is 3' long !1/16 x 3/8. Not opposed to using the 5/8 track you have if it works based on these pin. Looks like I need replacement pins as well. Thank you for any information. Bruce

I'm replacing my hollow wood bi-fold doors with metal bifold doors. I looked at the replacement hardware I would need from your thread with similar metal bifold doors. My question is, will I also need to replace my track, or can I purchase a wheel cap that will work with my existing track? Here are ... (cont.)

Can you tell me which track I should try to replace on my 1970's Metal Bi-Fold Closet Doors? I can't tell from the pictures if I need 21-401 or 21-452. Attached in my pictures are the doors, the track and hardware off one side of the doors.

I'm not able to tell what track I should purchase for my metal bi-fold doors. My doors are from the early to mid 70's. Our whole house has them but the one in the family room was replaced with wooden 6 panels (junk). The previous owner left the old doors in the basement thankfully. I am able to fin ... (cont.)

I need replacement caster piece that slides into the plastic sleeve and has the spring loaded caster on the bottom. Photos show: SLIMFOLD Model E door label; empty sleeve missing metal piece and caster; example of sleeve with metal piece and caster in place.Bob

Doors are 36w x 93.5L I would like to eliminate the bottom track period on it and it be top track only. There is no markings on any of these pieces. I need to know what I need to order for the doors parts wise.Regardless of the outcome of this post I will need new tracks as well. These doors are 49+ ... (cont.)

Looking for replacement parts for my doors.

I ordered 16 pivot clamps 21-154 tonight. I'm assuming they will work with the pins in my doors. The o/s diameter is 5/16". I'm also needing some pin caps for the 5/16" pins Do you sell these caps individually? If so I'd like to order some. Part #? Thanks for your assistance with this. Terr ... (cont.)

What do I need to make this bi-fold door work smoothly?It scrapes and is difficult to open and close.Thank you very much.MikeI will send pictures of track also. Perhaps that needs replacing too.

I need the hardware to get the door back on it's track. I want all the parts replaced and instructions on how to install it