Viewing all customer Discussions for:

21-062 Bifold Door Pivot, Leigh

I need help identifying the correct parts for the above door (95 inch doors).I don't know whether the diameters are 1/4 inch or 5/8 inches?? Thank You

I want to replace the pins for this old door, not sure which pins I need?

Hi , I am trying to replace hardware ( 3- pins pivots etc) to fix "one)leigh full view bifold door.

Would like to buy hardware for the following 2 doors. Leigh Full-Vu Metal Bifold Doors. Attached find label of door. Pics of the 4 corners of the door. Do you have replacement tracks for these doors? I can see that a spring and cotter pin is missing but have no idea if anything else is missing. ... (cont.)

No markings on any of the parts, unknown maker of the metal bi-fold door. Removed pin not knowing pics needed before removal. Pin in pics is 5 1/4" long x 1/4" diameter. Spring and cotter pin were on it. Plastic gasket in bottom and top of door holes (may be nylinders?) No plastic cap on top of ... (cont.)

Give me a Quote for 10 GUIDE PINS (5 1/4" x 1/4") and 2 Pivot Pins ( 5 1/4" x 1/4") ASAP. Thank you, Bobby

Hello, Need replacement plastic sliders for top and bottom rails. The pin is 5 1/4 inch long, 1/4 inch wide. I would also appreciate receiving information about a full set of replacement parts (top and bottom). No idea who manufacturer was. Thank you in advance.

For Leigh Full-Vu metal Bi-fold doors (see label photo), the pins & nylon parts are either missing or not holding due to wear, bending, etc. The pivot pins at the fixed ends appear to be fine. Your parts specifically say TOP. My question is whether the bottom pin assemblies that slide are identical ... (cont.)

We have 3 bi fold doors that need repair and one double bifold door that needs repair.They all need new stationary pins, plus the pins with the springs. the double bifold door keeps opening off the track, not sure if it piece that runs across the track is too short.Do we need two pins for each stati ... (cont.)

My door fell off the tracks and is not staying on the track. not sure which pins to purchase to repair. The door has a label that reads: Full-Vu Folding door Leigh Products INC. Coopersville Michigan

I purchased the following parts for my bifold door: 21-062 - pivot 21-054 - guide pin do you have any video's showing how to replace these parts on a Leigh Full-VU bifold metal closet door? Thank you.

I have a small linen closet with bi-fold door (Leigh Full-Vu door part #6956) which is most likely original to the building (from 1960's). The door won't glide along the track on the bottom of the floor - it gets stuck where the screw sticks up in the track. The top pins often come out of the top ... (cont.)

I need to replace one of these "fixed Pin" this one does not have a spring. I've identified several other parts and have an order to place and hope to do so shortly.

Hello, I'm trying to get all the components for a Leigh Full Vu steel bi-fold door. I looked on your website and came across what looked like the parts put wasn't sure. The one product code I found was 21-108 and at the bottom of that page was what looked like the parts I needed. ... (cont.)

I might be searching wrong, I need one of these pins. It's not 5/16, it's 1/4. It's for the same doors I got the parts for in my previous order. I'll need the pin, washer, nut and wingnut complete. Tnx

Hello,As you can see I have part #21-205 bracket. I am missing the pin that goes with it. Are you able to let me know what part I need? Not sure if the diagram is helpful.Thank you,Eve

I am looking for a bifold door bottom pivot, circa 1970, similar to your product code 21-048. The main difference is that the last 1/2 inch of the smooth section on mine is turned down to a diameter of 3/16 inch. The threaded section is 5/16 x 18. Do you have one that fits? Thanks, Al ... (cont.)

Hello, I need part numbers for both complete pins and brackets for bi fold doors as shown.

We need to purchase complete mounting hardware minus top and bottom track for 10 doors. Doors were manufactured around 1970. Thank you Jim

My appartment complex has about 300 leigh doors, all it says on the doors is quality control approval number 559245 I need hardware kits for the pins and the bushings that slide in the rails both top and bottom