Viewing all customer Discussions for:

21-150 1/4" Nylinder

Hello, I need part numbers for both complete pins and brackets for bi fold doors as shown.

I ordered 21-402 & 21-150 & 21-108 for a mirrored bifold closet doors. 21-108 does not fit in the track I ordered i talked to one of your reps and they said i need new pins and caps to fit the track she asked me to send pics of the old pins they. can you let me know what all i need to order to fit t ... (cont.)

Trying to figure out what parts to buy for top and bottom stationary and the ones that move also need plastic parts that go into track .basically need all the parts

I have a client who has 4 96" steel bifold closet doors, 41 years old in good condition, but missing all the hardware except for floor brackets and 2 original top tracks, I was wondering if you can tell me if you have the 8 top pins, springs and hardware( 4 pivoting, 4 guiding brackets) and the 4 bo ... (cont.)

I ordered grommet 21-163 and it is too large for my metal bi-fold doors. I have included pics of the original grommet above. Any help would be appreciated.

I am attaching the photos of my metallic closet bi fold door's hardware. Top pivot : refer top pivotphotos 5 inch long, 1/4" dia with a plastic washer or cap to hold the pin top and bottom of frame (on a door- See photo top- 8) And a two metal push nuts with cuts to hold the pin( photo no (1,2 ... (cont.)

I'm having some trouble locating the hardware for my bi fold doors. I've checked the stuff at the big box stores and it isn't long enough to fit through both holes and I cannot find the plastic bushings that the rods go in. Perhaps you can be of some assistance thank you.

I have two sets of US Plywood branded Metal Folding Doors. Both are obviously reasonably old. The metal and plastic fittings are worn or missing and I would like to buy 4 complete sets of parts, one for each corner, including the 4 moving metal sliders, which sit inside the channel rails, into which ... (cont.)

We need to purchase complete mounting hardware minus top and bottom track for 10 doors. Doors were manufactured around 1970. Thank you Jim

My appartment complex has about 300 leigh doors, all it says on the doors is quality control approval number 559245 I need hardware kits for the pins and the bushings that slide in the rails both top and bottom

I need help at getting the right size top and bottom pivots, for my bifold doors. I would also like to get more brackets for the pivots but don't know the right size. And while I'm at it I'm going to get the glide pins replaced.

Hi, I'm looking for hardware to use with this door. The pivots are okay but the guide pins and the guide brackets are destroyed. Can you guy's help with this?

I havre a set of bifold mirrored doors, with what appears to be 21-058 as the top guides ( only they are 4 1/4" long= complete with spring clip and guide. However the bottom guide ( not the pivot) seems to be 21-049 - ie no spring and that little nylon guide - actually two of them and it i ... (cont.)

I need to replace the track to my closet door. Attached are photos of the track that needs replacing along with the pins. The pins seem in good condition but the caps need replacing and maybe the springs. Can you please recommend replacements for these parts? Thank you.

I purchased subject (item# 21-044) but I cannot get it to function so that the pin moves up and down. It seems as if I need either 21-150 (nylinder) or a nylor grommet to enable it work. Please advise. Thanks

Good Morning, I have old Strato-Fold metal bi-fold doors that I need replacement hardware for (Serial #26629). I would like to speak to someone asap, to make sure I'm ordering the correct part numbers. I need; Caps (21-105)?, Cone Springs (21-256), and some Pins (complete w/caps & cone springs). ... (cont.)