Viewing all customer Discussions for:

21-150 1/4" Nylinder

I recently purchased a rebuild kit for ~1980s mirrored closet doors. I cannot get the pins to stay in the pin caps as the pins pull out when opening/closing the doors. I reversed the spring tension on the doors(top: push up vs pull down to engage pin) and the pins still will not seat in the cap. ... (cont.)

Pin hardware for 8 foot metal bifold doors. Need all hardware for 2 doors

We have 3 bi fold doors that need repair and one double bifold door that needs repair.They all need new stationary pins, plus the pins with the springs. the double bifold door keeps opening off the track, not sure if it piece that runs across the track is too short.Do we need two pins for each stati ... (cont.)

Metal bifold doors 36" wide by 93" high. Need new track and hardware. I can give more detailed information if you need it.

I have some Leigh Bi-Fold Full-VU Metal Doors Part # 8433. I have one bedroom with the top track still assembled and hanging from the ceiling. I have the bottom piece of wood in place, but need the track that will work with this door along with the parts. The track is right around 4' wide. Do you ... (cont.)

Need replacement bottom pins and a couple plastic sliders for the bottom rails. Pic1 shows top pivot pin (which I have all of), pic 2 shows bottom of a door, pic 3 shows the one bottom pin and the plastic slider that it snaps into. The rail is at (or just over) 7/16ths inch wide. The pin is 5 1/4 ... (cont.)

My door fell off the tracks and is not staying on the track. not sure which pins to purchase to repair. The door has a label that reads: Full-Vu Folding door Leigh Products INC. Coopersville Michigan

Hello I am in the process of remodeling my home and have 6 of these old closet doors. The doors are in great shape but the tracks and hardware are completely worn out. Do you sell replacement parts? Would be dissapointed to get rid of these doors. They are solid. Just old lol

Hi! Wasn't sure, I just couldn't find this size on your site so wanted to ask for help! This is for a mobile home bifold door system. Any help would be greatly appreciated! Thank you, Liz

I am renovating my place and decided to spray paint my old closet doors, unfortunately once I removed the doors the top pivots came off and the little plastic plugs are no longer keep them from springing out. I will need to order new top pivots and bottom pivots along with additional stationary pivo ... (cont.)

Need two end caps. Don't understand some assemblies have rubber washers and some don't. Are they necessary if the spring clip is on the shaft? Don't know if you sell the individual parts for the shafts or just the shaft and all accompanying parts. Let me know.Thanks,Marvin

Building is built maybe in late 1960? I want to replace all pivot parts at top and bottom.

I have a small linen closet with bi-fold door (Leigh Full-Vu door part #6956) which is most likely original to the building (from 1960's). The door won't glide along the track on the bottom of the floor - it gets stuck where the screw sticks up in the track. The top pins often come out of the top ... (cont.)

I need about 6 of these guide pins so I want to make sure I get it right. Can you help identify the correct pin? As you can see from one of the photos, the current pins (or the broken pins) were 4 1/2 inches long. These are metal doors, fairly old in my estimation. I'm sorry that some of the photos ... (cont.)

STRATO-TRACK INC. is stamped on horizontal bracing. Tracks are fine.

hello I'd like to refresh tired 50 years old metal bi-folds. Could you help me identify the parts shown in the attached pictures? Pictures are top left, top right, bottom right and left. I'd like to replace top and bottom tracks as well. thank you

found similar pins but they we're 5 1/2" long

I have two sets of metal bifold doors that are old and don't work well. They don't stay in their nylon clips, are hard to open and shut, etc. I think the tracks are still okay, so I want to get all new pins, springs, nuts, and nylon clips for top and bottom rails (I assume you can replace those by r ... (cont.)

I received bottom track for my metal bifold door, 21-401. Note 2 photos. I think you refer to the pieces as floater and pivot ? Your track is less wide as my old one. My floater piece (under the spring) is wider than the opening on the track and does not go in.I want to order the 2 parts (floate ... (cont.)

Hi! I need your help identifying which parts I need. I have three set of these doors. One on 36 inch tracks and two on 59 inch tracks. I would like to recondition these doors so they open and close nicely. Somebody at swisco showed me the 21-044. The the closest if not the se vracket would ... (cont.)