Viewing all customer Discussions for:

21-150 1/4" Nylinder

Bushing used as a glide in upper track for my bi-fold doors. Manufacturer unknown. ID is 1/4 inch, OD is 3/8 inch. Length is 5/16 inch. Flange OD is 5/8 inch. Flange thickness about 1/32 inch. Most critical measurement is ID and flange OD.

Hello I am sending photos of doors that I am to repair... if possible. I would like to see if you could check the pics out and determine if you have the parts... but... mainly... look at the pic where the bottom of the door has damage and whether it is worth repairing or not. This is for an elderly ... (cont.)

I have an old Leigh Metal Bifold door that needs a new bottom track, cap and bumper. Approximate measurements for the existing track are: Length 3' Width 1" Height 15/16". Would your Part 21-401 track be an acceptable replacement and what other parts would I need to finish the set up for the new tra ... (cont.)

We are looking for any replaceable parts to the Monarch Metal Bi-fold doors,We have 8 bi-fold doors (or 4 double doors) and some are missing parts at the top or bottom so they do not slide in the track.All of the hinge side of the doors are fine, so its only the top and bottoms where it slides in th ... (cont.)

HelloI moved into a condo with metal closet doors. One door is off the track and someone has tried to fix in the past. I think they are from the 70s. I hope I don't have to replace the tracks top and bottom. Photos are of parts that appear to be in need of replacement. I don't see any numbers or mar ... (cont.)

Helping one of my clients. They have 96' thin metal bi-folds and for one of the doors the bottom slider pin assembly is missing. I saw some similar parts listed, but they are not the same. Hope you can be of assistance, thank you in advance, Robert Lijs, EXIT Realty Metro.

I'll need replacements for these parts, as well as the top and bottom track. I'll send pictures of that as well. Thank you.

Hi There, I recently bought a couple used mirrored metal bifold closet doors to replace our wooden bifold doors. The bifolds are 36x80" in dimension. The wooden setup has single top track and bottom pivot bracket. I would like to have same setup but I'm willing replace the track, bracket, and ha ... (cont.)

my pins or the ones i am looking for are about 5.25 long with a .250 shaft with a groove for a hair pin clip and the cap on the top is about .410

I am looking for a metal bifold door track. see pictures below

I have a louvered metal bi-fold ( Made by National Door ) and it needs new hardware. I am attaching some pictures of the hardware in hopes that this might help. The tracks seem to be in pretty good shape.

I'm looking for track parts fittings for the doors

I have a FULL-VU closet door composed of two bi-panel elements. To repair it I started to document each element: top pivot 5/16" top glide 1/4" bottom pivot 5/16" bottom glide 1/4" A very wise decision as there appeared to be only simple pins and such. Actually each of the four locations, a ... (cont.)

The top guide wheel is not able to stay up seem to be missing an nylinder and bottom guide wheel is Bent Ned a replacement part Steel Full-Vu Door Leigh Products, Inc.

Pin Caps on 2 metal bi-fold doors with mirror-fronts in our home have become distorted and it is hard to open/close the doors. I bought some plastic items from your website on what I guessed to be the right products but I have a few quandaries. The attached pictures and dimensional data show the ... (cont.)

I am trying to fine the correct pins for a Flow Away ,steel ,mirrored ,bi fold closet door. The doors have two different types of pin holders. Most of the doors that work have white plastic bushings at the top an bottom of the steel door with some kind of black plastic for adjusting. These seem f ... (cont.)

I need 1/4 inch nylinders 2 pieces 21-150. Also need pin caps 4 pieces 21-108. I also have bumpers that are 7/16 inch by 1 1/2inches in lenght

one panel is sagging and is dragging on the bottom track. Was told it needs a new pin that will raise the door and lock it in place

I need both a top and bottom guide post assemblies for a National door which uses your part no. 21-113 guide on my track. Please include springs, clips and installation diagrams. Joseph W.

I had great success with one closet's bifold doors, and I thought the other door was identical. But it turns out it's really different. Do you know which parts I need?