Viewing all customer Discussions for:

21-209 Pivot Bracket, Benchmark

I need to replace the hardware for my Benchmark bi-fold closet door. I can't seem to find a part number on the closet door. Can someone please help me find the hardware kit? Left side door dimensions 23.5 L x 79 H.

Ihave the exact same doors. Here are some images of the guides and doors. The metal pins are 3/16" I am missing the glides and white caps and a couple of spring stops. I don't have a clue what they originally came with and how they should work, but would appreciate any input and suggestions for mak ... (cont.)

I need assistance identifying the parts needed for this metal bi fold door. Unfortunately, we do not know the brand of door. Any input would be appreciated. Thanks.

I received bottom track for my metal bifold door, 21-401. Note 2 photos. I think you refer to the pieces as floater and pivot ? Your track is less wide as my old one. My floater piece (under the spring) is wider than the opening on the track and does not go in.I want to order the 2 parts (floate ... (cont.)

I need top and bottom hardware. All parts pin,spring etc. Please help!

no names, numbers or markings available.

My PostBenchmark Steel Bifold Door came off the track. The doors are louvred from top to bottom. Need both posts to repair. One came completely off; the other is badly bent. The doors were installed in 1985. The one post looks like the 21-044. Your help is needed to get the correct parts and to ge ... (cont.)

I am trying to source parts for this Benchmark steel bi-fold door. Can you assist --it is installed on a track. will need the parts to hold it in place and open and close smoothly. thanks

I need bottom track from old glass bifold door

Swisco, This item broke in the bottom track of my bi-fold door. Can you identify it and do you have any replacement parts? Thanks.

Hello, I need to get a full set of parts for (2) sets of double doors. Do you have the parts in kit form? as opposed to individual?If I knew what parts I needed I would be able to order them. I'm redoing a condo that has your doors with parts missing. I don't know what parts they are, so if I coul ... (cont.)

I recently ordered some parts (listed below) for my metal bifold doors that I thought would fit perfectly, but I was too hasty and they didn't work, as you can see in the picture. Can you please help me choose the correct parts?

Hello, My daughter broke the pin on my laundry closet door. I do not want to replace the door to a lower quality wood door. I have included a few pics of the unbroken door that is next to this door. Please help me locate replacement parts. Thank you so much, Rebecca

Here are photos of parts, we need all the internal parts except the tracks. 3

Need four sets upper and lower track with pivot brackets for 1982 Benchmark Bi-fold louvered steel doors. Do you have replacement tracks?

Have these old metal bifold doors. I need help obtaining top and bottom pivots if such a thing.looked at YouTube video but as you can see the doors are a little different. Need parts. Thank you Brad

These pins need to be replaced. Do you have them?

We are looking for parts to secure bifold steel closet door by Benchmark. Most likely need to replace missing spring and cap to fit the track. The pins are about 5 1/2 inches or 14 cm long (a quarter inch or 6mm in diameter). Another spring was 2 3/8 inches or 6 cm long (1 cm diameter). The track ... (cont.)

Hello customer care. I am Doug Woods at 919-309-5563. I have six bifold doors that need a new threaded rod installed at the leading edge of the door. Please refer to the photograph within the attachment and get back to me if you have a part that would work for this. Thank you very much. Doug Woods ... (cont.)

Found no names, markings, or numbers on existing hardware. Pivot is a plastic block measuring 13/16" long, 5/8" wide, and 3/8" high with a 3/8" hole a little towards one end where the door pivot goes. There is a small hole on the side towards the other end where a 8/32 screw goes to hold the pivot ... (cont.)