Viewing all customer Discussions for:

21-209 Pivot Bracket, Benchmark

Bi folding metal closet door pins - about 6" long and 1/4 in dis. Missing 2 top pins in these metal closet doors.

Please help identify hardware.Not sure if this is original hardware or not. Need enough hardware to completely re-do two bi-fold doors. Long pieces measure 12

I have two sets of US Plywood branded Metal Folding Doors. Both are obviously reasonably old. The metal and plastic fittings are worn or missing and I would like to buy 4 complete sets of parts, one for each corner, including the 4 moving metal sliders, which sit inside the channel rails, into which ... (cont.)

These doors are in great condition but the track and pins seems to be on its last leg. The doors squeak horribly and keep coming off the track. Can you assist me in what parts I need to fix the door in perfect working condition again. Thank you. I have included pictures. The doorway for the doors is ... (cont.)

Below is the picture of the metal door I have. It did not have any pins on it. I purchased pins that move (114) in Home Depot for the top and bottom . I don't know what pin to use for the stationary pin on the bottom. The door is touching the floor and needs to be raised up. I saw your Bi-fold ... (cont.)

Good Morning; A few months ago (August 24, 2015, Order 673586) I ordered some components e.g. Pivot pin 21-044 for Benchmark metal bifold doors. The component are fine and I am planning to order more. I have these doors all over my house here in Maryland. One question I do have is I notice whe ... (cont.)

hii I have this closet door I need to buy replacement parts for it I about two feet wide metal and the bottom only has one circle thing at bottom and top I think you are calling it the pivot bracket. Should there only be one per rail ? Is it cheaper to buy these parts in a set or individual , also d ... (cont.)

we are rehanging a metal bifold door and the bracket that mounts to the floor rusted away and we need a replacement part. Looking at the parts on the site I don't believe it is shown. It is the pivot bracket into the floor. I would need the screws as well

I have older Benchmark doors and I need a couple of the sliding bottom rail pivot bracket. The part that the bifold pivot pin goes into. There is one on the top rail that has a place to screw into so the bracket can be used as a non-moving hinge bracket.Not sure if the same bracket is used as a slid ... (cont.)

I have several metal bifold closet doors in my apt but all of those hardware are old and not functional. Is it a good idea to just use the whole new set of pivots and guide pins like your video showed, instead to find the match because some are lost and hard to match? Which group are the best ... (cont.)

Hi, I'm looking for replacement parts for 2 Benchmark steel bifold doors. (Each door 291/2 wide, 781/2 high). I need both the upper and lower pivots and upper and lower guides for each door to include brackets.and springs. Do you carry these parts? Thanks!

Hi, I have a Benchmark Bi-Fold Steel Door for a hallway closet, for a home built about 1977. Most of the pins and other supporting hardware seem to be missing; we've had it off for a while but would like to rehang it. Is there a way to order a "one of everything" set of hardware that goes with ... (cont.)

I have 70's era Benchmark steel bi-fold doors on my pantry. I need new hardware for them but I can't identify which parts I should order. Can you help. The doors are 60 inches wide by 79 inches tall (total of 2 doors and 4 panels total. Marilyn

Does the 21-002 mate with the 21-209 or the 21-200 ? Also does the 21-404 include 2 pivot blocks or do they need to be separately ordered? Thanks

Due To Home Improvements I Had To Take Down All My Closet Doors And Hardware. I Have Put Them Back Up And They Just Don't Seem Right. Is There Complete Instructions for Installation and Adjustment For Benchmark ByFold Steel Doors. Thanks

Our doors are about 30 years old and are grinding metal on metal because of wornout parts. Please advise on all parts that should be replaced. Please contact me, I am sending photo's and would like to replace all parts that will make the doors run smoothly again

I think I have found some of my parts but would like help putting part numbers to the three items needed to repair my doors. I have attached 3 photos of the three items. please give me a call or email, would like to get started on the doors. Best Regards, Mike

We moved into a house that has the metal Benchmark bi-fold closet doors and they are a mess. They do not close at all properly and have made some observations. I noticed that the bottom stationary pivot pins, I believe the 21-002's are not inside the pivot bracket holes,but they should be correct? C ... (cont.)

I have a set of doors in my kitchen that are in front of a food pantry. I am not being successful in putting the doors back up. For For some reason the doors seem to be dragging on the bottom when being opened or closed. I have purchased pivot pins in the past but nothing seems to work. Springs ... (cont.)

I have a non-operative Benchmark door and looking at your website, it appears I need to replace both my 21-044 guide pins. However, how do I install and adjust them? A drawing or parts diagram would be helpful. Do the plastic tips on the 21-044 ride inside the track or on the surface of the track ... (cont.)