Viewing all customer Discussions for:

21-250 Spring

I ordered some parts from swisco recently and now I need a couple more but I'm having trouble finding what I'm looking for on your website. Parts I had ordered were 21-044 and 21-250 and 21-100.

I have a small linen closet with bi-fold door (Leigh Full-Vu door part #6956) which is most likely original to the building (from 1960's). The door won't glide along the track on the bottom of the floor - it gets stuck where the screw sticks up in the track. The top pins often come out of the top ... (cont.)

Need The spring inside

STRATO-TRACK INC. is stamped on horizontal bracing. Tracks are fine.

found similar pins but they we're 5 1/2" long

Ihave the exact same doors. Here are some images of the guides and doors. The metal pins are 3/16" I am missing the glides and white caps and a couple of spring stops. I don't have a clue what they originally came with and how they should work, but would appreciate any input and suggestions for mak ... (cont.)

I have two sets of metal bifold doors that are old and don't work well. They don't stay in their nylon clips, are hard to open and shut, etc. I think the tracks are still okay, so I want to get all new pins, springs, nuts, and nylon clips for top and bottom rails (I assume you can replace those by r ... (cont.)

I wrote to you a few moments ago about missing parts I need for my 1970's metal closet door. Now I have taken some photos, hoping they may help. Two photos show another door that has all its parts and works fine. One photo shows the top of the door that needs to be fixed and the parts are missing, ... (cont.)

Need 9 upper & lower guide pins and bushings, 4 top pivot pins and springs if required, and 3 adjustment (lower pivot) pins. See parts drawing photo for nomenclature. I need parts for a home sale asap!

Looking for replacement parts for metal bi-fold doors. Need pins, springs and pin secure clip. Pin is about 4 1/2 inches

HelloI moved into a condo with metal closet doors. One door is off the track and someone has tried to fix in the past. I think they are from the 70s. I hope I don't have to replace the tracks top and bottom. Photos are of parts that appear to be in need of replacement. I don't see any numbers or mar ... (cont.)

I need pin caps for sets of Leigh Full-Vu steel bi-fold doors. The part number on the door label is 6956. I need both upper and lower caps for 20 doors. I would like to send pictures but can't figure out how to send to an internet address. Can you help me with these? Thanks, Jim

I have a FULL-VU closet door composed of two bi-panel elements. To repair it I started to document each element: top pivot 5/16" top glide 1/4" bottom pivot 5/16" bottom glide 1/4" A very wise decision as there appeared to be only simple pins and such. Actually each of the four locations, a ... (cont.)

We are looking for parts to secure bifold steel closet door by Benchmark. Most likely need to replace missing spring and cap to fit the track. The pins are about 5 1/2 inches or 14 cm long (a quarter inch or 6mm in diameter). Another spring was 2 3/8 inches or 6 cm long (1 cm diameter). The track ... (cont.)

Hello, I need the top pivoting side of a leigh full-vu bifold door. I dont have the original one i am wanting to replace, though i believe the hole is 5/16th

How much vertical adjustment is there in this part. I have new carpets and need to raise doors at least 1/2 to 1 inch. I want to get new springs and clips, can this be done? Thanks.Paul

Need some mounting hardware as a few pins are missing and some exist but seem to have nothing holding them in place. The tracks appear to be in good order.

Trying to figure out what parts to buy for top and bottom stationary and the ones that move also need plastic parts that go into track .basically need all the parts

We need to purchase complete mounting hardware minus top and bottom track for 10 doors. Doors were manufactured around 1970. Thank you Jim

Here parts I need to repair the doors for my brother in law. First is a photo of a diagram and a bottom pivot pin assembly. I am hoping you can get all the info from the drawing for the parts. I would need. I would like to replace all the parts on the doors if possible. Our tracks appear to be good ... (cont.)