Viewing all customer Discussions for:

39-286 Casement Window Handle, fits Andersen

I have this operator on a vinyl replacement window. I would like to use this unit on an Andersen wood awning window from the 1960's. It's 41" wide x 18" high. I think I can modify the sash to receive the scissor hardware but I'm not sure if it will push that wide a window out properly. I like the 15 ... (cont.)

please help me identify this part and let me know how to replace it. Thank you

These are from windows installed in the late 1950's

For this window crank,39-146, do you have the wing nut style crank as opposed to crank 39-286.

do I need any extra parts to replace existing operator with 39-389 kit? thanks Chris

--these knobs tend to unscrew spontaneously, most of my handles are now w/o these knobs are replacements avail other than the whole handle would 39-298 work as replacement for handle 39-286 I need 21 knobs,and 8 full handles, or else 21 full handles funny how all these have disap ... (cont.)

I'm looking for a part. The crank for the window stopped working. The only part I could find a number for was the outside casing, which said "Andersen 7191-33." However, it is the inside part (operator?) that may be a problem. I attached pictures to hopefully reveal what the problem might be and ... (cont.)

Window part ID Needed

I'm having trouble getting the right crank for my casement window. I need an 11" long arm, but I can only find 9" and 13" arms on your website. Please help.

The operator for this casement window is stripped and will not open or close the window. The part is stamped "Standard-Themson Corp, Dayton, Ohio, USA, Patent Pending" The operator arms are both 16" long. The house was built in 1954 and the windows are perfect other than the 2 units are that th ... (cont.)

Hello, I need to replace the crank hardware for an Anderson window. I believe the windows were installed in the early 1990s. The photo shows that part of the plastic cover broke. This is not the main problem, however. When I turn the crank I can open the window but I cannot turn it to clos ... (cont.)

Do you id window operators by pictures? I was told by people it was an Anderson but some said it wasn't because there was no logo. It's one of those ones used in 60s -70s buildings so it's quite old. Please let me know if you could help me. Thank you!

I am looking for an Anderson window crank replacement and must be same exact size otherwise crank will hit sill. The corresponding part number is 7191-8. They seem to be smaller cranks than the ones I see at stores. Thanks for you help!

I'm looking to replace a couple of operators for Anderson awning type windows. The stamp on the operator is C-9400-1B The number on the arm is 1521101 Do you have the correct replacement operators?

The part # on this arm is C-9400-1 viewed from the top. Flipping it over, it is stamped F-9400-8 on the bottom plate.

Hi, let's start a conversation. How do I un-install a non working crank so we may identify it. I need about ten of these.

Hello, I

I ordered some 39-027E operators which seem to fit in every way except the end of the arm which goes into the track. My original hardware has square fittings on the end. Do you have this hardware or would I be better off changing my tracks to accomodate the 39-027E?

1. will this crank replace 1954 anderson casement window cranks? I have one replacement with the numbers 60-C_7041-62 that seems to work. But I need 32 of them. .2. on some of the handles only the top nob and the pin that holds it into the crank are missing. can i just replace the nob on these cran ... (cont.)

Hi, We have a rental property with Anderson casements windows on either side of a fixed pane window (pic attached). 3 of the casement windows are inoperable. One arm was stamped Anderson 55003 - you could see this on the arm after prying the window open. Will your 39-094 work on this windo ... (cont.)