Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

Hi there, Can you please help me identify the correct replacement part? Thanks Scott

Can someone please figure out which part I need to fix my window?

Unable to determine maker of windows. Looking for 3 sets

Hello, Just want to make sure I have correct part picked out before ordering. No Identifying markings on existing part but window weighs 26 lbs. Pretty sure I need a 385-27. 19-005 top and 15-004 shoe. Mine measures 1 3/32 deep and 15/16 wide. Because it weighs 26 lbs is it best to get 2640 or 2650 ... (cont.)

Hello,I need to replace two channel balances for a Milgard window (2610/2670), but I'm not sure which is the correct balance for it on your site.The printing on the balance reads: 26 5 KR CALDWELLThanks,-Tim

I have a 27" channel balance that I need to replace with a stamp of 2690. I see the Series 385 that you have looks like what I need, but it only goes to a 2670. Do you have a 2690? If not, will the 2670 work for my window (I haven't weighed it, but I can if this is a matter of weight of the windo ... (cont.)

It's 1/2 inch and the metal piece is 27 inches. Can't figure out which part of yours to order? The numbers on the side show 26 2 EW CMC 4 Don't think there is left or right, but need right if so. Thank you, Gary BTW a guy at Home Depot referred you.

May I change the rope?

27? long Markings 26 5 GW CMC 11

channel rail, the metal measures 27" not including the plastic. I'll also need plastic inserts for the window pane. I'll send that separate

HiMy channel balances have broken strings so I need to replace them. Cant figure out the exact model. I have attached pictures of the ends and following are the details. Any help would be appreciated. Length 27 inchesWidth: 1/2 inchMarking on the balance reads: 26 5 Caldwell

The broken channel balance has these numbers printed on them, "26 4 IV CMC 7". Am I correct in assuming that the 26 and 4 are equivalent to your model 2604? The old balance is 27" inn length as measured from end to end of the metal channel only.

Says 2630 GL on the part. Measures 27". The graph is 1/4 inch.

Hi! I need 4 milgard channel balances which are 27" long and 1/2" wide. RST 2640 I need 2 milgard channel balances which are 21" long and 1/2" wide. RST 2030J I see the guts (springs and strings, etc, and the shoes (feet) all are part of milgard window channel balances. I am attaching pictur ... (cont.)

Hi! Here are the pictures of my balance stamped 26 4. Thanks, Fred

I sent you the part numbers on the first email,however i will send them again they are as follows; 26 3 AX CMC 7. thank you Michael

It is marked with 26 3 KQ Caldwell and is 27" in length. there are no additional stamping or markings that I can tell

I have a Caldwell Sash Balancer that broke and try to understand what part number I need to order. It measures 28" long, tip to tip an 27" long is the alum channel. It's marked "26 3 CQ Caldwell. I'm attaching a picture and would appreciate it if you can tell what part to order. It looks like a 26" ... (cont.)

Could you recommend which weight option to choose when the actual window weight is at the top of one range, and the bottom of the other. My parents dont have much upper body strength so its important they can close the windows easily. I'm looking at the S385 series for both 33" and 30" balances. ... (cont.)

stamped 2630 and below is stamped BS1. I can not tell the difference in several of your units I need four for two windows.